-
This faceplate ring is ideal for holding small to medium sized bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 40 mm jaw set which comes with both the SC1 and SC2 Mini Chucks. Diameter: 68 mm -
Another of the most popular jaws for full size chucks – these are also ideal for smaller chuck projects too. We have set the range of these bodies to be compatible with most tea light holder designs (on either body) as well as many salt or pepper pot designs and these offer an excellent expansion grip for many projects. The end of the jawis dovetailed so can be used on its own as a delicate grip – or the jaw can be inserted full length using the back jaw face as a register and providing wall support to prevent the workpiece being knocked from a dovetail only grip. The dovetail at the end provides additional security in expansion mode.SC1 Expansion: 39 - 47.5 mm Contraction Spigot: 6 - 14.5 mm Contraction Square: 4.5 - 12 mm SC2 Expansion: 39.5 - 60 mm Contraction Spigot: 6 - 26 mm Contraction Square: 4.5 - 25 mm -
These jaws are perfect for drilling pen blanks, eliminating the need for a drill press and offering much more accurate results because the deep grip to all four sides ensures excellent holding power. Drilling on the lathe means the feed speed of the drill bit is under complete control, so a superior finish can be achieved on a wide range of materials. These jaws are also useful for working on small finials and similar projects, as in addition to their strong grip, the work piece is moved forward from the chuck to allow greater access. SC1 Contraction Spigot: 14 - 20 mm Contraction Square: 14 - 24.5 mm SC2 Contraction Spigot: 14 - 20 mm Contraction Square: 14 - 26 mm -
These jaws are able to hold the smallest work pieces. The convex internal radius on each jaw is designed to avoid damage to small and fragile work. It allows the user to get very close to support thin work as safely as possible. It also allows good access to work close to the base of a work piece without the tool fouling on the jaws. For maximum support always ensure the workpiece features a spigot long enough to be supported along the full length of the jaws’ internal surface. SC1 Contraction Spigot: 4 - 11.5 mm Contraction Square: 4 - 11.5 mm SC2 Contraction Spigot: 4 - 25.5 mm Contraction Square: 4 - 25.5 mm -
Standard fastenings spares kit for the Record Power SC3 and SC4 chucks. The kit contains 8 hex socket head screws for jaws, 3 and 4 mm hex wrenches and a blind set screw and fibre washer for chuck inserts. -
Out of stock
These nylon jaws are designed specifically to be cut with standard turning tools. They can be easily shaped to create bespoke jaws to fulfil exacting requirements and offer excellent grip without marking the work piece. Diameter: 118 - 140 mm Depth: 26 mm -
Out of stock
Record have increased the capacity of their larger remounting jaws, whilst ensuring they can still clear the bed of lathes with the popular 12” swing capacity and are capable of holding 275 mm (10 3/4”) diameter bowls in contraction mode. Remounting jaws are incredibly popular due to their flexibility. They work in both contraction and expansion modes and can be fitted behind other jaw sets to create bespoke set-ups to make turning more efficient. The soft stoppers are designed to hold without causing damage, making them ideal for remounting finished or partly finished objects for further work. -
Remounting jaws are incredibly popular due to their flexibility. They work in both contraction and expansion modes and can be fitted behind other jaw sets to create bespoke setups to make turning more efficient. The soft stoppers are designed to hold without causing damage, making them ideal for remounting finished or partly finished objects for further work. Expansion: 95 - 215 mm Contraction Spigot: 59 - 170 mm Contraction Square: 53 - 154 mm -
This large faceplate ring is ideal for holding large bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 50 mm jaw set which comes complete with all Record Power chuck packages. Must be used with: 62313 50 mm Standard Jaws (Supplied with SC3 and SC4 chucks) Diameter: 100 mm -
These jaws are fantastically effective for drilling pen blanks. They eliminate the need for a drill press and offer much more accurate results and the deep grip to all four sides ensures incredible holding power. Drilling on the lathe means the feed speed of the drill bit is under your complete control, meaning a superior finish can be achieved on a wide range of materials. These jaws are also useful for working on small finials and similar projects as in addition to their strong grip, the work piece is moved forward from the chuck, allowing greater access. Contraction Square: 10 - 26 mm Contraction Spigot: 11 - 20 mm Expansion: 35 - 64 mm -
To complement the new pin jaws, the mini spigot jaws have also been improved. These jaws perform many of the same tasks in expansion and the extra screw hole profiles and added teeth to the outside provide tremendous grip for when this area will not be visible in the finished work piece. This set has been given a 13 mm internal diameter, making it ideal for turning strong spigots on knobs and handles, again adding to their versatility. Expansion: 26 - 46 mm Contraction Spigot: 13 - 33 mm Contraction Square: 11 - 31 mm -
Records' new pin jaws have been improved by squaring the external shoulder to allow workpieces to properly register against the back of the jaws. This is ideal for use in expansion, to grip tubes in work pieces such as pepper or salt grinders. We have also reduced the internal diameter to 9 mm, making it ideal for making finials or lace bobbins - Thereby increasing its versatility. This set is ideal for miniature turning and to grip workpieces internally without excessive damage or marking. Expansion: 28 - 45 mm Contraction Spigot: 9 - 28 mm Contraction Square: 7 - 27 mm -
These extremely flexible jaws feature internal and external dovetails for bowl work. The deep internal grip is versatile but main benefit of these jaws is to project the work away from the chuck, allowing good tool access to the base of the timber for cleaning and shaping. Expansion: 54 - 74 mm Contraction Spigot: 38 - 58 mm Contraction Square: 27.5 - 48 mm -
These new jaws are ideal for heavy bowls and vases. The wide front face provides a good register for the base of the bowl or vase and the deep toothed body provides strong grip on the spigot. The internal gripper can also be used on smaller rough green timber. Also featuring an external dovetail in expansion, they can be used for large platters. A truly versatile and solid jaw set. Expansion: 81 - 102 mm Contraction Spigot: 46 - 65 mm Contraction Square: 33 - 54 mm -
Featuring a specialised dovetail profile, these jaws are ideal for turning up to 30” bowls. They also feature a reverse dovetail for a contracting grip on large spigots. Expansion: 125 - 145 mm Contraction Spigot: 104 - 123 mm Contraction Square: 74 - 94 mm . -
Featuring a specialised dovetail profile, these jaws are ideal for turning large bowls, green timber and hollow vessels. They combine the profile of our previously popular 100 mm dovetail jaws with a deep body and internal teeth to improve versatility. The outer dovetail jaws are ideal for large bowls or platters, particularly when gripping onto a spigot and the deep internal toothed body is ideal for large spigots of large hollow vessels. Expansion: 94 - 114 mm Contraction Spigot: 76 - 95 mm Contraction Square: 54 - 74 mm -
These jaws are a smaller version of the standard 50 mm jaws, featuring the same dovetail profile in expansion and the superb grip of the hawk beak design on contraction. Designed specifically for smaller spigots and recesses, this set is incredibly versatile and makes a great addition to any turner’s tool collection. Expansion: 38 - 58 mm Contraction Spigot: 28 - 47 mm Contraction Square: 16 - 37 mm -
This faceplate ring is ideal for holding medium sized bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 50 mm jaw set which comes complete with all Record Power chuck packages. Must be used with: 62313 50 mm Standard Jaws (Supplied with SC3 and SC4 chucks) Diameter: 87 mm -
Designed with an internal dovetail to fit securely onto the standard 2" (50mm) jaws. These rings work in the same way as normal faceplates but with the convenience of the easy chuck fitting. Available with an outer diameter of 3⅛" (80mm) and 4¾" (120mm). -
These extended jaws act like a pin chuck, expanding into a pre-bored hole. A useful technique for free form edge bowls as you don't have to bore an exact size as with other pin jaws. The longer jaws allow for a very powerful spigot grip for smaller work. Also features a small dovetail. Expansion 26 - 46mm Contraction square: 28 - 7mm Contraction spigot 31 - 10mm
