Black

  • Out of stock

    While this resin has been manufactured to resist scratching and resistance to marking from heat sources we must stress this resin will still mark if sharp items are moved across the surface or hot items are placed on the surface.

    As with all casting products, we stress that customers should purchase a small amount to perform initial tests to ensure suitability for their project and requirements.

    Product Data Units Mix
    Mix Ratio  Weight 100 : 50
    Hardness  ShoreD 80 - 85
    Viscosity (25°C) mPa.s 600 - 900
    Density (25°C) g/cm3 1.09 – 1.13
    Pot life (200g, 25°C) Mins 25 - 30
    Cure Time (200g, 25°C) Hours 24
    Full Cure (25°C) Days 7
    Recommended Casting Thickness mm 1 - 5
    Pigmentation Epoxy pigments are the recommended system to colour this resin however the polyester range of pigments will also work. Please read the Technical and Safety Data sheets prior to use. We recommend small scale testing to ensure compatibility before using at full scale.   Cold Weather Notice Cooler temperatures in the UK and Ireland around mid-autumn to mid spring are not ideal conditions for water clear epoxy systems, this can increase the chances of crystallisation in the resin (this can occur at room temperature depending on circumstances, it is however much less common). Appearance can differ depending on the degree of crystallisation, from small lumps sitting on the surface to a hazy/milky white appearance, extreme cases the contents may completely solidify.  Crystallisation occurs due to a phase change from liquid or solid similar to that of water turning to ice, fortunately it is easily reversed by warming the epoxy component to 60°c.  Ensure any crystals are completely removed as remaining crystals can act as a seed causing the crystals to form again quite quickly. Lab results show the heating cycle to remove crystals can be repeated on multiple occasions before beginning to suffer from any losses in resin properties.   We recommend keeping the resin system at a good room temperature at all times where possible, ensure to clean the lids and bottle necks of containers with isopropyl alcohol / acetone allowing the solvent to evaporate before replacing the lid.  
  • Milliput Epoxy Putty

    £2.65£4.75
    Milliput Epoxy Putty, the two sticks have a long shelf life but once mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. Speed of hardening is dependant on temperature and at normal temperatures (20-25ºC) Milliput becomes rock hard in three to four hours. By the application of heat the setting time can be reduced to a few minutes. After setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time at the same temperature. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted. Milliput can be sandpapered and painted immediately it has set. (it is advisable to wear eye protection during this process). Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive and should not be used where a paste, mucilage or thin glue is indicated. Milliput will set under water and is heat resistant up to 130°C. Shelf Life: Recommended that Milliput is stored in cool, dry conditions. Please reseal bags after use. Stored correctly this product should remain workable for about 2 years. Available in six colours: Standard (Yellow/Grey), Terracotta, Silver Grey, Black, Superfine White and Turquoise Blue.
  • An exciting and vibrant set of colours for staining wood, Spirit Stains are methanol based to make them quick drying and because of this they also will not raise the grain of the timber they are applied to. The pigments used to make this stains are of the highest quality and all score the top ratings of 7s and 8s in the Blue Wool Scale, the measuring system used to rate fade resistance. This means you can use them with confidence knowing that the colour you apply will still be the same many years later. Spirit Stains are fully inter-mixable so you can produce virtually any colour you can think of, giving you full opportunity to be as creative as you wish. The colours will also mix after application so you can blend from one colour to another for fantastic ‘flare’ effects. Spirit Stain White is designed primarily as a mixer to create pastel shades when mixed with other Spirit Stain colours. It can be used to stain timber but as it is a translucent stain this can have a limited effect depending on the base colour of the timber used. Should you want a more subtle colour you can dilute the stains with Spirit Thinners for a delicate wash effect.
  • This exciting range of water-based acrylic paints comes in 8 metallic colours. Designed to add an even shimmer to your work they will really make it glow. Mix and match them, use them to highlight certain areas or cover everything in them, the choice is yours. Best used over sanding sealers, apply a spray lacquer over them once dry to seal them in. Can be applied by cloth, brush, spray gun, air brush or any suitable medium you choose!
     
  • Hampshire Sheen - Lacquer 500ml Aerosol have been formulated to be strong, flexible and very glossy. They can be used for both internal and external projects. Glass like finishes can be achieved with these two superb acrylic spray lacquer products. Supplied in 500ml cans with 2 nozzles.
  • Hampshire Sheen embellishing wax is designed to be used on open grain woods such as oak or ash and works brilliantly to highlight textured  elements on tighter grained woods. Use in conjunction with the Intrinsic Colour Collection for stunning results. Supplied in a 130g lever lid tin. Apply liberally and buff to a gloss.  
  • Hampshire Sheen Embellishing Wax are ideal for enhancing open grained decorative items from woods such as Oak or Ash or woods with added texture.  They work brilliantly in combination with the Intrinsic Colour Collection and this selection available in nine colours are a great, easy to apply alternative to gilt creams. Supplied in 60g tins.
  • Hampshire Sheen Intrinsic Colour Collection, individual bottles of the Intrinsic Colour Collection in 125ml size, twelve shades of colour developed and mixed by Martin Saban-Smith. 
  • Hampshire Sheen Intrinsic Colour Collection, individual bottles of the Intrinsic Colour Collection in a large 250ml size, twelve shades of colour developed and mixed by Martin Saban-Smith. 

Title

Go to Top