-
Long series sawtooth Forstner cutter Long series forstner bit (inch), sawtooth pattern, particularly suited for cutting down the grain. Long series - all sizes are a minimum of 150mm long, will produce over-lapping holes, resharpenable. -
Long series sawtooth Forstner cutter Long series forstner bit (mm), sawtooth pattern, particularly suited for cutting down the grain. Long series - all sizes are a minimum of 150mm long, will produce over-lapping holes, resharpenable.
-
The parabolic flute design clears the chips quickly. Precise when boring into end grain. Packed in reusable tubes with euro slot. -
Forstner Extension bar shanks are available in two sizes, to suit Planet's long series saw tooth forstners: 3/8" collar /200mm long Forstner Extension Bar. For sizes 3/8" to 2" 1/2" collar /280mm long Forstner Extension Bar. For sizes 2 1/4" to 4" -
Designed with an internal dovetail to fit securely onto the standard 2" (50mm) jaws. These rings work in the same way as normal faceplates but with the convenience of the easy chuck fitting. Available with an outer diameter of 3⅛" (80mm) and 4¾" (120mm). -
These extended jaws act like a pin chuck, expanding into a pre-bored hole. A useful technique for free form edge bowls as you don't have to bore an exact size as with other pin jaws. The longer jaws allow for a very powerful spigot grip for smaller work. Also features a small dovetail. Expansion 26 - 46mm Contraction square: 28 - 7mm Contraction spigot 31 - 10mm -
Featuring a specialised dovetail profile, these jaws are ideal for turning large bowls, green timber and hollow vessels. They combine the profile of our previously popular 100 mm dovetail jaws with a deep body and internal teeth to improve versatility. The outer dovetail jaws are ideal for large bowls or platters, particularly when gripping onto a spigot and the deep internal toothed body is ideal for large spigots of large hollow vessels. Expansion: 94 - 114 mm Contraction Spigot: 76 - 95 mm Contraction Square: 54 - 74 mm -
Featuring a specialised dovetail profile, these jaws are ideal for turning up to 30” bowls. They also feature a reverse dovetail for a contracting grip on large spigots. Expansion: 125 - 145 mm Contraction Spigot: 104 - 123 mm Contraction Square: 74 - 94 mm . -
This faceplate ring is ideal for holding medium sized bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 50 mm jaw set which comes complete with all Record Power chuck packages. Must be used with: 62313 50 mm Standard Jaws (Supplied with SC3 and SC4 chucks) Diameter: 87 mm -
These jaws are a smaller version of the standard 50 mm jaws, featuring the same dovetail profile in expansion and the superb grip of the hawk beak design on contraction. Designed specifically for smaller spigots and recesses, this set is incredibly versatile and makes a great addition to any turner’s tool collection. Expansion: 38 - 58 mm Contraction Spigot: 28 - 47 mm Contraction Square: 16 - 37 mm -
This large faceplate ring is ideal for holding large bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 50 mm jaw set which comes complete with all Record Power chuck packages. Must be used with: 62313 50 mm Standard Jaws (Supplied with SC3 and SC4 chucks) Diameter: 100 mm -
These new jaws are ideal for heavy bowls and vases. The wide front face provides a good register for the base of the bowl or vase and the deep toothed body provides strong grip on the spigot. The internal gripper can also be used on smaller rough green timber. Also featuring an external dovetail in expansion, they can be used for large platters. A truly versatile and solid jaw set. Expansion: 81 - 102 mm Contraction Spigot: 46 - 65 mm Contraction Square: 33 - 54 mm -
These extremely flexible jaws feature internal and external dovetails for bowl work. The deep internal grip is versatile but main benefit of these jaws is to project the work away from the chuck, allowing good tool access to the base of the timber for cleaning and shaping. Expansion: 54 - 74 mm Contraction Spigot: 38 - 58 mm Contraction Square: 27.5 - 48 mm -
To complement the new pin jaws, the mini spigot jaws have also been improved. These jaws perform many of the same tasks in expansion and the extra screw hole profiles and added teeth to the outside provide tremendous grip for when this area will not be visible in the finished work piece. This set has been given a 13 mm internal diameter, making it ideal for turning strong spigots on knobs and handles, again adding to their versatility. Expansion: 26 - 46 mm Contraction Spigot: 13 - 33 mm Contraction Square: 11 - 31 mm -
These jaws are fantastically effective for drilling pen blanks. They eliminate the need for a drill press and offer much more accurate results and the deep grip to all four sides ensures incredible holding power. Drilling on the lathe means the feed speed of the drill bit is under your complete control, meaning a superior finish can be achieved on a wide range of materials. These jaws are also useful for working on small finials and similar projects as in addition to their strong grip, the work piece is moved forward from the chuck, allowing greater access. Contraction Square: 10 - 26 mm Contraction Spigot: 11 - 20 mm Expansion: 35 - 64 mm -
Records' new pin jaws have been improved by squaring the external shoulder to allow workpieces to properly register against the back of the jaws. This is ideal for use in expansion, to grip tubes in work pieces such as pepper or salt grinders. We have also reduced the internal diameter to 9 mm, making it ideal for making finials or lace bobbins - Thereby increasing its versatility. This set is ideal for miniature turning and to grip workpieces internally without excessive damage or marking. Expansion: 28 - 45 mm Contraction Spigot: 9 - 28 mm Contraction Square: 7 - 27 mm -
Out of stock
These nylon jaws are designed specifically to be cut with standard turning tools. They can be easily shaped to create bespoke jaws to fulfil exacting requirements and offer excellent grip without marking the work piece. Diameter: 118 - 140 mm Depth: 26 mm -
Out of stock
Record have increased the capacity of their larger remounting jaws, whilst ensuring they can still clear the bed of lathes with the popular 12” swing capacity and are capable of holding 275 mm (10 3/4”) diameter bowls in contraction mode. Remounting jaws are incredibly popular due to their flexibility. They work in both contraction and expansion modes and can be fitted behind other jaw sets to create bespoke set-ups to make turning more efficient. The soft stoppers are designed to hold without causing damage, making them ideal for remounting finished or partly finished objects for further work. -
Remounting jaws are incredibly popular due to their flexibility. They work in both contraction and expansion modes and can be fitted behind other jaw sets to create bespoke setups to make turning more efficient. The soft stoppers are designed to hold without causing damage, making them ideal for remounting finished or partly finished objects for further work. Expansion: 95 - 215 mm Contraction Spigot: 59 - 170 mm Contraction Square: 53 - 154 mm -
Record SC4 Professional Geared Scroll Chuck Package with no insert is perfect for the demanding woodturner, being capable of holding large work pieces yet possessing the precision and compactness to handle more delicate work. This model features an enclosed back with full indexing plate and has pinions driven by a long ball ended hex key to make access easy, even when large work pieces are mounted. This chuck is an insert model which means it is easily future proofed against upgrades and can be used on multiple lathes, even if they have different spindle threads (additional optional inserts required).Supplied complete with the deep wood screw, 50 mm standard jaws, 2” faceplate this package offers professional performance at an exceptionally affordable price.Please order SC4 chuck insert to suit your lathe -
Specially designed to provide a strong contracting grip to unsupported spigot turning applications, e.g. vases and goblets. It can handle spigots from 30mm (13/36inch) to 50mm (2inch). Also features expanding grip mode.
-
Record SC3 Chuck Package is lighter and more compact than the SC4, making it ideal for use on any lathe, particularly small to medium sized machines and is still compatible with the full jaw range. The compact design reduces load on the lathe spindles and bearings and gives good access to smaller work pieces. The large jaw slides offer unrivalled strength and holding power that cannot be found in other chucks of this size.Supplied complete with the deep wood screw, 50 mm standard jaws and 2” faceplate this package offers unrivalled value. -
Chuck Insert to fit the Record Power SC1 Mini Chuck and SC4 Professional Geared Scroll Chuck only. -
This modular tool rest system enables the turner to build up a collection of tool rests without going to great expense. Six different rests are available: 4", 6" and 9"as well as a 9" curved internal and external and a box platform which can be used in conjunction with just one stem. Cross bars are specially hardened to avoid those troublesome nicks and to give a smooth finish. Stems are available in ½", ⅝", ¾", ⅞", 1", 25mm, 28mm and 30mm diameters to fit most popular lathes. The same stems are compatible with the Precision Boring System. -
The original Stebcentre is an invaluable accessory for every woodturner. Fitted in the lathe head-stock it is a boon for both the novice and the experienced. Its ring of sharp teeth ensure that the Stebcentre bites the wood to give more security and more drive. Because there are several points of contact there is minimal risk of splitting. The Stebcentre can be used with equal confidence on both soft and hardwoods as well as synthetic materials. In its patented design the Stebcentre also features a spring-loaded point. By slightly backing off the tail-stock the work piece still remains resting between the revolving centre and the Stebcentre. This allows the turner to inspect his work without the need to switch off the lathe. Where time is a critical factor the Stebcentre is ideal as the work-piece can be quickly removed without stopping the lathe. Overall length: 4". Patent No. 2286138 -
Largely inspired by Norwegian turner Petter Herud a series of Revolving (or Live) Stebcentres has been introduced. Not only do these offer the same degree of security as the conventional Stebcentre, but they have allowed the turner to experiment with basic off-centre turning. Visit www.robert-sorby.co.uk to download instructions on how to produce multi-sided dishes and bowls. -
Cross bars are specially hardened to avoid those troublesome nicks and to give a smooth finish. -
This heavy duty belt and disc sander has plenty of power to handle demanding sanding whilst also being capable of fine and delicate work. The solid cast iron table provides ample support and the 1 hp motor provides plenty of power to avoid stalling under pressure. Shown with optional leg stand.
-
for use with BDS150 for 6" x 4" Belt & Disc Sander -
The BBS1 is a hugely versatile machine, particularly useful for tight curves as well as more sweeping contours, this bobbin sander allows beautiful, crisp results to be achieved with ease. The machine comes with two bobbins and corresponding table inserts and a range of additional sizes are also available. The BBS1 allows a wide array of shaping tasks to be accomplished with ease, from intricate craft projects to larger work on cabinets, chairs and much more. In addition, the powerful and quiet 1/2 hp induction motor ensures larger timbers can be handled effectively and easily. The finely ground cast iron surface also helps easy movement of the timber whilst providing extremely solid support. The build quality, features and versatility of this machine makes it an essential tool in almost any workshop. -
for use with BDS150 for 6" x 4" Belt & Disc Sander -
With a cast iron table at the heart of this compact machine it is designed to offer those with limited space or budgets a real bandsaw with sensible capacity and performance, as an alternative to lightweight hobby machines. The BS250 should not be confused with the lightweight hobby machines available in the market at a similar price. It shares the same essential build qualities as its larger cousins – strong steel frames, dynamically balanced bandwheels, cast iron tables and an induction motor. It has been designed to offer the user with space restrictions a serious machine in compact form. The machine can be bench mounted or fitted to the optional stand and wheel kit, providing great flexibility in a tight space.
-
The BS300E is a great all rounder perfectly specified for the medium sized workshop where a range of duties will be required.Featuring a solid fence, vital for accurate ripping, which has a heavy extrusion mounted on a cast iron base and fixed to a solid steel bar for maximum rigidity and support. This is based on an industrial Startrite design and much more solid than other fences at this level. The machine also features a solid double trunnion fence mount to provide rigid table support and one-handed table tilt on a smooth rack and pinion. Adding to the structural integrity of the BS300E are the cast iron bandwheels which are fitted with precision ground rubber tyres to provide a flywheel effect for smooth cutting. A solid blade tension indicator is fitted to the rear of the machine to allow for easy setup. The BS300E is also supplied with a basic wheel kit as standard. -
An ideal workhorse for the busy workshop where power and generous capacity are required but budget and space do not allow a bigger machine. This features an open legstand, often requested by our users as it provides greater stability and can be used with an optional pedal style wheelkit. A basic wheelkit is provided as standard. The bandwheels are cast iron and dynamically balanced with precision ground, crowned rubber tyres usually only found on much more expensive industrial machines – the flywheel effect of the cast iron wheels improves cutting performance and speeds. Our tables are some of the largest in their category and a one piece cast double trunnion has been designed to provide even greater support and rigidity. The rip fence is the strongest and most industrial in its category with a chromed fence and the mount machined from a single piece of cast iron. The extrusion itself is a heavy section to provide rigidity and accuracy. -
Skip tooth pattern to suit BS250 & Sabre 250. Also fits RSBS10, Clarke CBS335, Nutool HBS14 -
Skip tooth pattern to suit BS300E. Also fits Startrite 301S/301E, Poolewood 1402, Scheppach Basato 3
-
Outside caliper with fine adjustment for measuring spindle diameters when turning between centres.
-
Divider with fine adjustment for measuring between two points, scribing circles prior to turning, marking along a spindle etc. -
Inside caliper with fine adjustment suitable for measuring internal dimensions, eg turned boxes. -
Outside caliper with fine adjustment for measuring spindle diameters when turning between centres. -
The Robert Sorby ProEdge takes all the guesswork and effort out of sharpening all your woodworking, woodturning tools. The ProEdge has an abrasive belt which is a quick and efficient method of putting a keen edge on each and every tool. The cool running belt avoids any overheating. The ProEdge comes complete with aluminium oxide and zirconium belts. The ProEdge requires no complex assembly - it can be plugged in and used straight from the box.
-
The ProEdge Deluxe system includes a skew jig, a standard gouge jig, a fingernail profiler and three different belts in addition to the basic system. -
Out of stock
Featuring a spiral twist, these plain end HSS blades can cut in any direction without the need to turn the workpiece. This is particularly useful for projects that are too big for the throat depth of the scroll saw. They also allow for pieces to be cut with the bevel running in the same direction all round. 0.8 mm wide, 0.34 mm thick, 40 TPI. -
These pin end blades are ideal for use in machines that only accept pin end blades, but can also be used in machines that feature universal jaws. Their width makes them ideal for straighter cuts and for more arduous cuts, such as deep hard woods. Perfect for small joints and box making. 3 mm wide, 0.5 mm thick, 20 TPI. -
These pin end blades are ideal for use in machines that only accept pin end blades, but can also be used in machines that feature universal jaws. Their width makes them ideal for straighter cuts and for more arduous cuts, such as deep hard woods. Perfect for small joints and box making. 3 mm wide, 0.5 mm thick, 15 TPI.
-
These pin end blades are ideal for use in machines that only accept pin end blades, but can also be used in machines that feature universal jaws. Their width makes them ideal for straighter cuts and for more arduous cuts, such as deep hard woods. Perfect for small joints and box making. 3 mm wide, 0.5 mm thick, 10 TPI
-
The width of these pin end blades makes them ideal for straighter and more arduous cuts, such as deep hard woods. The tooth pattern makes them ideal for faster cutting as they provide better chip clearance than standard tooth patterns. 3 mm wide, 0.5 mm thick, 9 TPI. -
The width of these pin end blades makes them ideal for straighter and more arduous cuts, such as deep hard woods. The tooth pattern makes them ideal for faster cutting as they provide better chip clearance than standard tooth patterns. 2 mm wide, 0.25 mm thick, 18.5 TPI.
-
The skew jig is for accurate sharpening of woodturning skew chisels. -
Out of stock
The standard gouge jig allows easy sharpening of all standard ground woodturning gouges. -
The woodworking chisel jig accurately ensures a straight cutting edge on any woodworking chisel. -
The long grind jig helps you create three different fingernail profiles on bowl and spindle gouges. -
The cutter holder is a great and inexpensive sharpening accessory. Being double ended it allows the turner to hold comfortably almost every Robert Sorby tool tip without the fear of catching fingers on a sharpening belt or grinding wheel.
