-
The ideal way to experiment with the different colours available to decide which ones you prefer, the Spirit Stain Kit contains one bottle (min. contents 25ml) of each of the twelve wood colours. These are exactly the same stain as in the bigger bottles and will intermix if you want to vary the shades available. The stains are very fade resistant, quick drying and non-grain raising. -
An exciting and vibrant set of colours for staining wood, Spirit Stains are methanol based to make them quick drying and because of this they also will not raise the grain of the timber they are applied to. The pigments used to make this stains are of the highest quality and all score the top ratings of 7s and 8s in the Blue Wool Scale, the measuring system used to rate fade resistance. This means you can use them with confidence knowing that the colour you apply will still be the same many years later. Spirit Stains are fully inter-mixable so you can produce virtually any colour you can think of, giving you full opportunity to be as creative as you wish. The colours will also mix after application so you can blend from one colour to another for fantastic ‘flare’ effects. Spirit Stain White is designed primarily as a mixer to create pastel shades when mixed with other Spirit Stain colours. It can be used to stain timber but as it is a translucent stain this can have a limited effect depending on the base colour of the timber used. Should you want a more subtle colour you can dilute the stains with Spirit Thinners for a delicate wash effect. -
These Dispensing Nozzles are, in fact, almost indispensable! They fit onto any of Chestnuts' plastic bottles in the 250ml, 500ml and 1 ltr sizes, simply replacing the existing cap. Cut the tip off to the size you want and use the handy cover to reseal them when not in use. A useful by product of using these is that if you knock a bottle over the amount you lose through the small nozzle will be much less than without it. Just don’t forget to take the nozzle off the bottle before you throw it away so that you can re-use it! These nozzles are not child resistant, the correct closure should be replaced when the product is not in use. -
This exciting range of water-based acrylic paints comes in 8 metallic colours. Designed to add an even shimmer to your work they will really make it glow. Mix and match them, use them to highlight certain areas or cover everything in them, the choice is yours. Best used over sanding sealers, apply a spray lacquer over them once dry to seal them in. Can be applied by cloth, brush, spray gun, air brush or any suitable medium you choose! -
These extended jaws act like a pin chuck, expanding into a pre-bored hole. A useful technique for free form edge bowls as you don't have to bore an exact size as with other pin jaws. The longer jaws allow for a very powerful spigot grip for smaller work. Also features a small dovetail. Expansion 26 - 46mm Contraction square: 28 - 7mm Contraction spigot 31 - 10mm -
Iridescent Paints give a change in hue, a slight colour shift when viewed from different angles and are especially effective on irregularly shaped items.Available in nine different amazingly bright and vibrant colours –- Green
- Azure
- Purple
- Red
- Turquoise
- Cerise
- Pink
- Yellow
- Vivid Blue
The paints are water based acrylics and can be applied by brush, cloth, spray gun/airbrush or any manner of ways to give interesting decorative effects. -
Iridescent Paints give a change in hue, a slight colour shift when viewed from different angles and are especially effective on irregularly shaped items.Available in nine different amazingly bright and vibrant colours –- Green
- Azure
- Purple
- Red
- Turquoise
- Cerise
- Pink
- Yellow
- Vivid Blue
The paints are water based acrylics and can be applied by brush, cloth, spray gun/airbrush or any manner of ways to give interesting decorative effects. -
This acrylic Reducer is the perfect thinner/flow medium for our Iridescent Paints and Metallic Paints, essential when using an air brush. Use sparingly, only a little should be required. This will also ensure that it does not affect the opacity and brightness of the colours. -
Keep your air brush in tip-top condition by using our Air Brush Cleaner after every use. -
End Seal is an emulsified paraffin wax used the seal the ends of freshly cut timber to slow down the drying process and reduce the risk of the timber splitting. It can also be used on work-in-progress that is being left unfinished where there is a risk of the timber splitting. Apply it liberally, normally by brush but it can be sprayed if needed, usually to the smallest surface of the timber which will normally be the end grain where moisture is most likely to escape from. Sealing the surface will encourage the moisture to escape via the larger areas which will result in a slower exit. -
Gilt Creams are a creamy, waxy paste with metallic flakes and pigments in them, giving a rich, lustrous finish to whatever they are applied to. The can be used for a ‘limed’ effect over a lacquer to give a high contrast effect, or uniformly over a piece and polished to a bright shine once dried. Available in- Gold
- Silver
- Copper
-
The Buffing Tree comprises of three 6 inch wheels, in the A, B and C cloth grades, firmly held on a central spindle. It’s ideal for buffing small items and, after loading the wheels with the compounds and wax, allows you to move from one wheel to the next in quick succession, dramatically reducing the time otherwise taken up by changing wheels. Ideal for polishing small items such as fruit, pens, boxes etc in batches. Requires one of our mandrels to fix to the chuck and a live centre for support at the tailstock. PLEASE NOTE: The Buffing Tree does not come as kit containing the mandrels and compounds etc; this is deliberate as if you already use the Buffing System you will have these and won’t want to buy them again. If you do not have these items they are available to purchase separately or as a pack in the Buffing Accessory Pack. -
These unstitched, cotton mops are ideal for polishing the insides of bowls and boxes etc to achieve the same great finish on the inside as on the outside when using the Buffing Wheel kit, without the fear of the item being snatched from your hands by the larger Buffing Wheels. All of the domes share the same thread as in the large mandrel and the small mandrel so all parts are completely interchangeable. Due to the smaller size of these dome buffs they will require more time and sometimes more speed on the lathe to be able to match the finish given by the larger wheels. Dome Buff A is used with compound 1 to cut back the applied finish and remove any minor blemishes left behind by sanding. Dome Buff B is used with Compound 2 to cleanse the piece and also to prepare for the final polish coat by giving an exceptionally smooth surface. Dome Buff C is used with either the Carnauba wax stick, microcrystalline wax or Microcrystalline Wax Stick to give a wonderful, long lasting shine. -
This kit gets you started on the road to buffing – all you need to supply is the lathe, a chuck and something to buff! Inside the kit you get the mandrels for holding the Buffing Wheels in the chuck. One of each buffing wheel (A, B and C) are included in the 8 inch size, complete with all the fixings attached to fit into the Mandrels. A bar of each of the compounds is included to get you started, these will last a long time so no need to worry about getting spares yet (although all of the items in the kit are available separately when you need to get them). Next is a stick of carnauba wax for that final gloss finish. Last but not least is a full set of instructions on how to use the kit to get the best from it. -
These compounds are designed to co-ordinate with the cloth used in the Buffing Wheels and Dome Buffs to give an exceptional cut and prepare the surface to a very smooth finish prior to using wax. Compound 1 -the brown one – (sometimes referred to as tripoli) is used with the ‘A’ Wheel/Dome to help smooth the applied finish. Avoid overloading the wheel/dome where possible to prevent a build up of the compound. If this happens it can be removed by either washing in soapy water or abrading the edge of the wheel with a coarse abrasive. Do not use on very open grained light coloured timber as the compound can get lodged in the grain and colour the piece. Compound 2 – the white one – (sometimes referred to as white diamond) acts as a cleanser to remove any traces of Compound 1 left on the surface (but not from the grain) and also has a very fine abrasive contained in it which smooths the work, leaving a semi-gloss finish and a superb foundation for the top coat of wax. Use Compound 2 sparingly, too much on the wheel will result in smears on the surface of your work which can be removed with buffing but this can be very time consuming and frustrating. It’s always best to apply a little and add more if needed. -
These cotton wheels come complete with the fixings needed to attach them to the mandrels in the Buffing System. Use Wheel A with Compound 1 for a preparatory cutback Use Wheel B with Compound 2 for an ultra fine surface prior to waxing Use Wheel C with Carnauba Wax Stick, Microcrystalline Wax or Microcrystalline Wax Stick. -
These Mandrels are available separately or come as part of the buffing wheel kit. Both Mandrels are made in the UK and are zinc plated for maximum protection. Due to the limitations of plating a blind hole care should be taken to ensure the tapped thread of the large mandrel stays as dry as possible. The large mandrel is designed to be held in a lathe chuck. It is 25mm in diameter at its widest part, stepped to 18mm with an undercut for smaller chucks. It can be held on either, both will still give plenty of clearance from the chuck. The small mandrel is designed to be held in a jacobs chuck or similar and is especially suited to use with the smaller 4 inch wheels and the Dome Buffs. -
All the items you need to use our Buffing System except the wheels – the perfect add-on when buying the Buffing Tree, the 8 inch wheels or the 4 inch wheels or the Dome Buffs The kit comprises of the Large Mandrel, the Small Mandrel, Compound 1, Compound 2, Carnauba Wax Stick. ALL OF THESE ITEMS ARE INCLUDED IN THE BUFFING WHEEL KIT. -
Chestnut Drill Polishing Brush has natural bristles that might seem a little harsh for polishing waxes but in fact are ideal for the task. Chestnut Drill Polishing Brush, which fits any electric drill or can also be used with the Buffing Wheel System, will give a higher gloss and more resilient finish to any waxed piece. In use, the bristles splay out in a mushroom shape, making this brush ideal for polishing spindles and cylinders. It can be used on flat surfaces but is prone to leave rings so the drum brush or dome brush are recommended for this application. The stock of the brush is about 10cm and the bristles are 4cm long. If the bristles of the brush become clogged with wax simply wash it in warm soapy water and allow to dry before use. -
Made in the USA, these are the original and best quality Foam Brush. Manufactured using a special foam with a stiffener inside to make sure they keep their shape in use, and supplied with a solid wooden handle attached. Great for eliminating brush marks (no bristles = no brush marks) and there’s no danger of any stray bristles coming loose and spoiling your work. Priced to be semi-disposable they will normally wash out several times for re-use. Fantastic for applying acrylic finishes which have a tendency to froth up when applied by brush – the Foam Brush virtually eliminates this completely. Can also be used for painting, particularly gloss paints, seasoned users have been known to have a brush in each hand! -
NyWeb pads are a non-woven nylon webbing with an abrasive – either silicon carbide or aluminium oxide – embedded into them to give an exactly defined cut.- The Green pads are 400 grit
- The Red pads are 600 grit
- The Orange pads are 1000 grit
- The White pads do not contain an abrasive and are thus technically non-abrasive, but the very texture of the pads gives them an incredibly fine – but immeasurable – cut.
-
Safety Cloth is a thick, non-woven paper cloth. Designed to stay wet longer to assist the transfer of finishes to your chosen surface, it also tears very easily if it gets caught in revolving parts thus avoiding the danger of fingers being dragged into machinery. The texture of Safety Cloth ensures that a thin, even coat is applied and the thickness means that it retains it’s strength and the same piece can be used several times with the same finish. Safety Cloth is not a replacement for common sense and good safety practise. -
The finest of Steel Wool, very low crumble and virtually oil free to ensure there is no contamination of your work. Use it after sanding with abrasive sheets to give an ultra smooth surface, or to apply waxes to smooth the timber whilst applying a thin coat. Steel Wool burns very quickly and easily; keep it away from sources of combustion (i.e. sparks etc). Always use a knife or scissors to cut Steel Wool -
Tack Cloths are coated with a special, sticky resin. The resin doesn’t transfer off the cloth but when you wipe it across a surface it picks up and dust and removes it, leaving behind a clean surface ready for finishing. This makes it ideal for use after your final sanding to make sure that all of the sawdust generated is removed and doesn’t affect your finishing. Tack Cloths are supplied in a sealed wrapper; once opened store them in an air-tight container to prevent them from drying out. Do not use Tack Cloth with the lathe running. -
This bleached knitted cotton cloth is ideal for applying and buffing most products; the slightly coarse texture ensures that the applied coating is spread thinly, which is always preferable. Not recommended for use on the lathe. -
These beautiful micaceous-based colours are for artists and crafters who wish to add a touch of glamour or glitter to a piece, such as the translucent glow of an angel's wings, a butterfly, a fish or the brilliant iridescent shimmer on a mallard drake's neck. Simply mix the iridescent colours directly into your paints or apply after decorating to highlight specific areas. The choice is yours. For best use when using the Iridescent paints in an Airbrush, looks well on an ebonised background. -
Use as a wipe on sealer (2 coats) prior to applying High Build Friction polish or Melamine Lacquer. Very quick drying (3-6 minutes). -
Although French polish is the general term for all types of Shellac Polish, it is also a product in its own right. Mylands range contains many blends of Shellac Polish which have been developed over the years to fulfil various different requirements – some of which are slightly modified products for a specific purpose. They come in various depths of colour, which give the French Polisher latitude to choose the most appropriate product for the timber being polished. Shellac products have a variety of uses from finishing antiques and reproduction furniture to acting as a barrier between two normally incompatible finishes. They are particularly useful when refurbishing furniture as they will seal in any wax product which may have been applied to the furniture in the past. -
Shellac Sealers are used in the French polishing trade either; as a quick drying finish to seal timber after staining; or as a basecoat for subsequent coats of French Polish. -
Used for diluting French polish, Light Fast and Earth Stains, or cleaning surfaces and tools.
-
Sold world-wide as probably the market leader in Friction polish. After sanding surface very smooth, seal with either Cellulose Sanding Sealer or Lacacote Wood Sanding Sealer (wiped on). -
Mylands wax polishes are manufactured from the finest natural ingredients including pure Beeswax and Carnuba wax. Mylands wax will help hide any surface scratches and produce a deep traditional sheen. On polished surfaces use sparingly and buff within a couple of minutes.