-
A stylish one-piece elegant looking twist pen. For this pen use sierra pen bushing set and 27/64 drill bit. -
Used to square the ends of the pen blank prior to turning and assembly. Mounts in drill chuck or universal pen mandrel. Suitable for 8.5mm, 9.5mm & 10mm pens. -
Twist Pen with ball end clip, available in Chrome, Gun Metal or Gold. Black ink refill, for this pen use 7mm bushing set. -
Twist Pen with double bead centre ring, black clip. -
Out of stock
7mm Twist Pen with broad band centre ring, black clip. -
A low sheen finishing oil based on Tung Nut Oil, Beeswax, Citrus solvents and anti-fungal oils that penetrates the timber substrate to nourish, preserve and seal; as well as providing protection against weather degradation and rot. A natural alternative to petroleum hydrocarbons and water based oils
-
A penetrative, nourishing, quality finishing oil which reflects the original, heavy-oil formulations that traditional Danish Oils were renowned for. As a clear finish will richly enhance the existing woodcolour/s. For best results, requires quality dry-sand surface preparation; using 600 /1200 / 1500 grit papers (the finer the better) Upon curing/drying (min. 14 days) makes for ideally prepared surface for further (optional) Waxing/Polishing. -
Out of stock
The standard gouge jig allows easy sharpening of all standard ground woodturning gouges. -
Forstner Extension bar shanks are available in two sizes, to suit Planet's long series saw tooth forstners: 3/8" collar /200mm long Forstner Extension Bar. For sizes 3/8" to 2" 1/2" collar /280mm long Forstner Extension Bar. For sizes 2 1/4" to 4" -
Cross bars are specially hardened to avoid those troublesome nicks and to give a smooth finish. -
Out of stock
The slim blade allows for a very fine parted section to be achieved. This is especially useful when grain match after parting is required. e.g. parting a lid from its box. The blade is 1¼" deep giving strength to such a thin section which eliminates flex and vibration. -
Out of stock
The Elipse range of respirators are made in Great Britain. The mask body is made from TPE (Thermo Plastic Elastomer) a flexible material which is designed to fit the contours of the face to provide a tight seal. The filter material is known as HESPA (High Efficiency Synthetic Particulate Airfilter). Together they provide absolute protection for woodworkers. The Elipse P3 has the highest classification for a particulate filter. Surpassing the European standard EN143 by achieved 99.98% filtration at 0.3 micron. It is therefore ideal for woodturners and woodworkers, giving complete protection, even when sanding. The twin filter arrangement consists of a light weight half face mask that is comfortable to wear for long periods of time. The low profile filters provide an unobstructed field of vision. Two adjustable elastic straps securely fasten the mask to the wearer. The two strap system allows the wearer to quickly put the mask on and off the face, whilst still wearing it around the neck. Can be worn with glasses ,without causing any steaming, and other PPE safety products including visors and helmets. It is perfect for everyday use by hobby and professional users. Other applications include metalworking, welding and stonemasonry. The Elipse P3 provides protection against dust particles, metal fumes (smoke), asbestos, oil and water mists, vapours, bacteria and viruses. Replacement filters are easily fitted. -
A dark brown to sometimes nearly black wood with straight to interlocking grain. Hard and heavy with good working qualities. Turns and finishes well and takes a good polish. -
Sale!
Another 'Crown' special, the Wedge tool is 'user friendly'. Superb for making coves on spindle work and finish cuts on both faceplate and spindle projects. It also provides a smooth finish when making goblets. A recent innovation, the Splay Tool can be used as a Skew Chisel, a Box Scraper, a Shear Scraper and also for detail work on spindles. -
Gift Card available to use against any product or course. -
- The multi-tooth drive centres feature a ring of teeth around the circumference of the tip, with a central drive point to give accurate positioning. This design gives an extremely strong grip, thanks to the many points of contact in the timber, which also minimises the risk of splitting the timber.
-
- The design of the 6-prong drive centres offers an enhanced grip to timber using the principle of opposing tooth profiles. The central point of the tool secures the drive centre in place, the six teeth around it grip the timber securely and the opposing tooth pattern ensures the wood fibres are pulled together to reduce the chance of splitting. Having two more teeth than the traditional 4-prong drive centres, they are ideal for use on hardwoods and larger pieces of wood.
-
Record Power's powerful work lamp is a perfect addition to any workshop. The long flexible neck allows it to be positioned to illuminate even the most hard-to-reach areas and get rid of troublesome shadows, giving a clear view of the work in progress. To further increase the lamp’s flexibility, a sliding collar on the lamp head allows either a spotlight or floodlight beam to be created. The strong magnetic base and magnetic side clip mean the light can be secured virtually anywhere on a machine. Powered by either standard AA batteries or a USB rechargeable lithium battery, this lamp gives hours of uninterrupted use and is ideal for a wide variety of machines such as scroll saws, bandsaws, sharpening machines, lathes and many more.Includes:• Magnetic base• Magnetic side clip• AA and Lithium battery holders• Micro USB-A cable -
Ever wished you had a finish that was as easy to use as shellac but with the durability of polyurethane? Well wish no more, because here it is.
This unique Hardened Shellac creates a film with a high resistance to heat, water and alcohol, yet it is used in exactly the same was as any normal shellac. It can be applied with a rubber as French polish, brushed, sprayed and dipped.
HOW IS THIS POSSIBLE? After shellac has been dissolved in ethanol* it is possible to introduce additives that cause the shellac to cross link after it has dried. This cross linking takes about 20 days to completely cure, less in hot weather.
USES: Ideal for table tops and other horizontal surfaces such as dresser and desk tops, etc. Also brilliant for use on guitars, lutes, harps and many other musical instruments where a traditional finish is required and good resonance qualities are essential.
NEW IMPROVED FORMULA In February 2009 U-beaut began adding a plasticiser to Hard Shellac. This gives elasticity to the cured finish, to combat crazing on the thin walls of musical instruments, whilst still having the same high resistance to marking from water, alcohol and heat it has always had.
-
Hampshire Sheen Intrinsic Colours being water based, they are non-flammable, environmentally friendly and afford you a long working time. They sink deeply into the wood and preserve the appearance of the figure in the wood, releasing the hidden subtleties. Apply more than one coat of dye to build up depth of colour, and add a black or earth undercoat for an even more dramatic effect. For the adventurous colourist, Intrinsic Colours can be mixed together to create even more shades or thinned with water for a lighter shade. -
Two-part clear cold cure lacquer for use on wood, hardboard, cork and plastic laminates. Extremely good adhesion, resistant to heat, solvents and abrasion. Can be burnished to a mirror like gloss or rubbed down to a smooth, satin finish with steel wool and wax. An excellent finish for marquetry as it does not darken light coloured veneers and does not yellow or craze on ageing. Hard-dry within 2 hours of application. Plastic Coating conforms to The Articles in Contact with Food Regulations. -
These jaws are fantastically effective for drilling pen blanks. They eliminate the need for a drill press and offer much more accurate results and the deep grip to all four sides ensures incredible holding power. Drilling on the lathe means the feed speed of the drill bit is under your complete control, meaning a superior finish can be achieved on a wide range of materials. These jaws are also useful for working on small finials and similar projects as in addition to their strong grip, the work piece is moved forward from the chuck, allowing greater access. Contraction Square: 10 - 26 mm Contraction Spigot: 11 - 20 mm Expansion: 35 - 64 mm -
Out of stock
New generation P3 R half mask, with low profile ergonomic design.- Offers less breathing resistance.
- Less clogging pressure and inward leakage.
- Approval P3 (R) APF20 x WEL
- Protects the user against airborne particles, oil aerosols, mist, welds and fumes.
- Twin HEPAC* pleat encapsulated design filter provides 99.99% filtration of airborne particles and aerosols at 0.3 micron and above.
- Exhalation valve on bottom of face piece, ensuring no exhalation fumes steam or fog of any glasses/visors.
- Protective grill covers 100% of filter surface.
- Grill protects filter from moisture and particulates, ensuring it performs better in clogging pressure and filtration efficiency.
- Unique integral sample port and plug allow non-destructive face fitting.
- Large non-return valve.
- Single piece head and neck strap with quick release.
- Manufactured from high-grade materials, odour free, non-allergenic. TPE mask body is latex and silicone free.
- Conforms to half mask standard BS EN 140.
- Respiratory protection to BS EN143 P3R.
- *High Efficiency Particulate Air Composite.
- Protection against airborne Coronavirus
-
Woodturners drill chuck, supplied with chuck key. -
A plastic dust collector hood with a wide mouth at one end and a round hose connection at the other. Suitable for use with standard 100mm diameter flexible hose. You may need a hose clamp to secure the hose to the round end (100HC). Ideal for Collecting dust and chips from small lathes, sanding discs or any other machinery which did not originally come supplied with a purpose made dust collection point.
If being used with a multiple branch hose system, a shut off gate (100G) can be attached using a sleeve (100SL) to join the two parts together. A hose can be attached to the other end of the gate and secured with a clamp (100HC).Charnwood DH410 Specification Mouth Opening 410mm x 320mm Hose Connection 100mm Diameter Depth 260mm -
Designed to hold wood securely without splitting, this drive centre gives superior hold. The opposing tooth profiles mean that as they enter the wood, the fibres are pushed together rather than apart, holding the timber together. -
Only the heartwood of cocobolo is used; it is usually orange or reddish-brown, often with darker irregular traces weaving through the wood. The heartwood changes colour after being cut, and can be polished to a lustrous, glassy finish; being quite dense, sometimes having a specific gravity of over 1.0, it will sink in water. The sapwood (not often used) is a creamy yellow, with a sharp boundary between it and the heartwood.
-
Designed with an internal dovetail to fit securely onto the standard 2" (50mm) jaws. These rings work in the same way as normal faceplates but with the convenience of the easy chuck fitting. Available with an outer diameter of 3⅛" (80mm) and 4¾" (120mm).
