Hazardous Good

Polycraft Clear Top 5 Epoxy Resin 1.5kg Kit

Polycraft Cleartop 5 Epoxy Resin 1.5kg Kit

£39.50

While this resin has been manufactured to resist scratching and resistance to marking from heat sources we must stress this resin will still mark if sharp items are moved across the surface or hot items are placed on the surface.

As with all casting products, we stress that customers should purchase a small amount to perform initial tests to ensure suitability for their project and requirements.

Product Data	Units	Mix
Mix Ratio	Weight	100 : 50
Hardness	ShoreD	80 - 85
Viscosity (25°C)	mPa.s	600 - 900
Density (25°C)	g/cm3	1.09 – 1.13
Pot life (200g, 25°C)	Mins	25 - 30
Cure Time (200g, 25°C)	Hours	24
Full Cure (25°C)	Days	7
Recommended Casting Thickness	mm	1 - 5

Pigmentation Epoxy pigments are the recommended system to colour this resin however the polyester range of pigments will also work. Please read the Technical and Safety Data sheets prior to use. We recommend small scale testing to ensure compatibility before using at full scale. Cold Weather Notice Cooler temperatures in the UK and Ireland around mid-autumn to mid spring are not ideal conditions for water clear epoxy systems, this can increase the chances of crystallisation in the resin (this can occur at room temperature depending on circumstances, it is however much less common). Appearance can differ depending on the degree of crystallisation, from small lumps sitting on the surface to a hazy/milky white appearance, extreme cases the contents may completely solidify. Crystallisation occurs due to a phase change from liquid or solid similar to that of water turning to ice, fortunately it is easily reversed by warming the epoxy component to 60°c. Ensure any crystals are completely removed as remaining crystals can act as a seed causing the crystals to form again quite quickly. Lab results show the heating cycle to remove crystals can be repeated on multiple occasions before beginning to suffer from any losses in resin properties. We recommend keeping the resin system at a good room temperature at all times where possible, ensure to clean the lids and bottle necks of containers with isopropyl alcohol / acetone allowing the solvent to evaporate before replacing the lid.

Details Quick View

Zip kicker spray, 2oz

£9.00

Accelerates Super Glue cure time. Best working accelerator for ZAP. Sets in just a few seconds.

Add to cart Details Quick View
Chestnut Acrylic Sanding Sealer 500ml

£14.52

This water based sanding sealer gets the job done without the smell associated with solvent based sealers and also with no flammability issues – ideal for asthma suffers and anyone with an aversion to solvent based finishes. Applied by cloth, brush or spray (Chestnuts' foam brushes are especially good with this) the sealer dries in about 5 minutes and can be overcoated with most compatible finishes after about 20 minutes although two hours should be left if using Acrylic Lacquer. Acrylic Sanding Sealer sands easily with a fine abrasive and is supplied ready for use.

Add to cart Details Quick View
Chestnut Cellulose Sanding Sealer

£13.80 – £24.90
Good finishing requires a good foundation, and Cellulose Sanding Sealer is probably the best way of providing one. Compatible with everything in the Chestnut Products range that benefits from the use of a sanding sealer (which is pretty much everything apart from oil finishes!) it is superbly universal. The purpose of a sanding sealer is manifold.

It seals the open pores of the timber prior to the application of the next coat, meaning that more of it stays on the surface and less of the finish is needed. Not only does this make it economical, when finishing the thinner the applied coat the less likely it is to get damaged, so a sanding sealer will help the top coats be more resilient.

Sanding Sealers also bind the loose fibres of the timber together giving a more solid foundation for the next coat, which helps make sure the final finish is able to adhere properly and thus be more durable.

They also include a sanding agent which acts as a lubricant to make the sanding process easier – the sanding agent also stands slightly proud of the surface of the sealer and it is this that is denibbed – the sealer itself should still be intact after sanding.
Select options Details Quick View
Chestnut Cellulose Thinners

£12.00 – £21.65

This pure cellulose solvent is a high quality dilutant for our cellulose based products, such as Cellulose Sanding Sealer and Melamine Lacquer. Thinning these products can help to make them easier to apply, especially over larger areas as it helps them flow out. Cellulose Thinners is also useful for cleaning any spills you may have in the workshop and is strong enough to help clean most things, taking care to ensure that it does not attack It can also be used to thin Spirit Stain to give a delicate wash effects, although spirit thinners is the better option for this.

Select options Details Quick View
Chestnut Shellac Sanding Sealer

£19.50 – £36.15

Shellac Sanding Sealer is the traditional way of sealing timber prior to applying a polish or a wax. Chestnuts version has a high percentage of real shellac which means it does the job extremely well, dissolved in an ethanol solution to make it easy to apply and quick drying. Applied by cloth, brush or spray it dries in about 20 minutes, making it very popular for cabinet and architectural work as it is easy to keep a wet edge running. It is also popular with woodturners and highlights the natural grain of the timber extremely well. Sand back lightly after application and apply Friction Polish, French Polish or any of Chestnuts waxes on top. Conforms to EN71 Part 3 – suitable for toys and nursery furniture.

Select options Details Quick View
Chestnut Spirit Thinners 500ml

£9.75

This clear, slower drying solvent is primarily for thinning our Spirit Stain to give delicate wash effects without affecting the colour (as methylated spirit would). It can also be used to dilute Friction Polish or French Polish if needed (usually only when the cap has been left off and the product has thickened up). It’s also suitable for use in making french polish if you want to dissolve shellac flakes in it.

Add to cart Details Quick View
Chestnut Food Safe Finish 500ml

£12.74

Food Safe Finish is a clear, food grade mineral oil. Chestnut use a thin grade of oil to allow it to soak into bare timber which then protects it against water splashes etc whilst not tainting or affecting the food in any way. It dries to a fairly matt finish; it is however ideal to use for wet sanding and when used with a very fine abrasive it can give an exceptionally smooth surface which has its own gentle glow. Apply with a clean cloth or brush direct onto bare wood, up to three coats are recommended. If the oil sits on the surface and won’t soak in it means the timber has absorbed as much as it can and no further coats are needed. Any surplus can be removed with a clean cloth if required. Depending on the way the item is used it might be necessary to top-up the finish, especially if it is washed regularly.

Add to cart Details Quick View
Chestnut Finishing Oil 500ml

£12.74

Chestnut Finishing Oil is Chestnuts' version of Danish Oil* and uses Tung Oil as its base but with the addition of solvents and driers. This aids the drying of the product and speeds it up dramatically, so that it’s dry within eight hours. It has a pale amber colour and dries to a hard yet flexible film which is very hardwearing and water resistant. For a high gloss finish apply several coats with a light rub down between coats; after 5 or 6 coats a good sheen should be visible. Finishing Oil is normally applied by cloth but on larger areas a brush can be used very successfully.

Add to cart Details Quick View
Chestnut Hard Wax Oil (Satin) 500ml

£19.20

If you’re looking for a clear finish that is tough, hardwearing and gives a satin lustre yet is still very easy to apply, even on larger areas, you’re in the right place. Hard Wax Oil is a particular blend of tough oils combined with special waxes which dries to an exceptionally resilient finish. Ideal for anything that is going to be subjected to water splashes or a lot of handling this oil may not be indestructible but it will stand up to a lot of abuse. It retains the ease of application typical of an oil and it stays wet long enough to get a smooth, even finish – even on large areas – but is touch dry and tack free in about 20 minutes, and better yet is ready for a second coat after about four hours (in normal conditions). Hard Wax Oil will build to a bright gloss finish after 2-3 coats. Rub down lightly between coats with a fine abrasive. Once hard dry (allow at least 24 hours) it can be brought to an even brighter shine using either the buffing wheel system or burnishing cream. For a not-quite-so-bright finish use a mild abrasive to reduce the gloss. For best results lubricate the abrasive with microcrystalline wax to retain the toughness of the oil.

Add to cart Details Quick View
Chestnut Hard Wax Oil (Gloss) 500ml

£19.20

If you’re looking for a clear finish that is tough, hardwearing and gives a bright gloss yet is still very easy to apply, even on larger areas, you’re in the right place. Hard Wax Oil is a particular blend of tough oils combined with special waxes which dries to an exceptionally resilient finish. Ideal for anything that is going to be subjected to water splashes or a lot of handling this oil may not be indestructible but it will stand up to a lot of abuse. It retains the ease of application typical of an oil and it stays wet long enough to get a smooth, even finish – even on large areas – but is touch dry and tack free in about 20 minutes, and better yet is ready for a second coat after about four hours (in normal conditions). Hard Wax Oil will build to a bright gloss finish after 2-3 coats. Rub down lightly between coats with a fine abrasive. Once hard dry (allow at least 24 hours) it can be brought to an even brighter shine using either the buffing wheel system or burnishing cream. For a not-quite-so-bright finish use a mild abrasive to reduce the gloss. For best results lubricate the abrasive with microcrystalline wax to retain the toughness of the oil.

Add to cart Details Quick View
Chestnut Lemon Oil 500ml

£13.40

If you’re looking for a finish that won’t change the colour of your timber, won’t overpower the natural beauty of the wood with a high gloss but will still protect the timber and smell nice, well, you’re in the right place! Lemon Oil is a clear, low build finish. By that we mean that it’s a very thin liquid with a very low solids content, so no matter how much you apply it’s not going to build up to a discernible visible film on the surface. Instead it soaks in and seals the surface, offering a level of water resistance and protection against handling. Normally applied with a brush or a cloth it’s very easy to use and covers well and doesn’t usually show overlaps, so it’s ideal for large areas which often look better without a high gloss. And as you might expect, it has a pleasant lemon aroma too, although this does fade after a while.

Add to cart Details Quick View
Chestnut Melamine Lacquer

£15.45 – £26.80

When you’re looking for a hard-wearing, heat and water resistant, quick drying gloss lacquer you need look no further than Melamine Lacquer. Based on cellulose technology, Melamine Lacquer has a catalyst suspended within it; when the lacquer is in the can it is inert but once applied and exposed to the air, the lacquer dries within five minutes like a cellulose and then the catalyst kicks in and the lacquer goes on to chemically cure to give a more durable coating. 90% of the curing process happens in the first seven days after application, making the lacquer very hard wearing, the remaining 10% of the process can take up to two weeks more to give maximum toughness, something you only need to consider if the lacquer is going to be subjected to extremely hard use. Melamine Lacquer is designed to give a full gloss finish which will be achieved with a very careful application. It can be applied by brush (foam or bristle), cloth or by spraying. Where necessary, use cellulose thinners to dilute the product – especially helpful if working on a large area. The gloss level of Melamine Lacquer can be increased by using burnishing cream once it has dried, and it can also be overcoated with friction polish (to increase the depth of the shine) or woodwax 22 or microcrystalline wax (for a more natural feel).

Select options Details Quick View
Chestnut Friction Polish

£20.13 – £36.90

Friction Polish is a shellac based polish ideal for creating a high gloss finish on or off the lathe. It’s a great decorative finish and is ideal for small items but can be difficult to apply to larger items on the lathe (over about 8 inch diameter). The high amount of shellac in Friction Polish does two main things. Firstly it helps seal bare wood and give it a great shine, which is good. Sadly the price of this commodity shot up a few years ago when the shellac crop failed and it never went back down, meaning that the cost of the polish has also risen sharply. Nevertheless, Friction Polish remains one of the most popular finishes for turners. It can be applied to bare wood but is normally used over a sealer and any of the sealers in the Chestnut Products range are suitable for this. Applied with the lathe running it dries almost instantly and builds to a deep, rich shine very quickly. Avoid using too much as this can cause ‘rings’ to appear on the surface. Friction Polish can be applied off the lathe with great success, using it like a French Polish and rubbing it into the surface. This does require a large amount of elbow grease (sadly not something we supply) but the end result is well worth the effort!

Select options Details Quick View
Chestnut French Polish 500ml

£17.56

Confusingly, French Polish refers to a range of polishes (which would include Button Polish, White Polish, Garnet Polish etc) and also to a specific polish, French Polish. Chestnuts' French Polish is a traditional blend of solvent (methylated spirit) and a top quality unbleached shellac which is very similar to a Button Polish in colour. Applied either to bare timber or over a Shellac Sanding Sealer it is built up in many layers which have been described as being the thickness of a cigarette paper! French Polish gives the rich amber glow found on fine antique furniture and requires a very specific technique for application that is time consuming and laborious, but the final effect has to be seen to be believed and the satisfaction of achieving it is its own reward. A French Polish finish is not very hard wearing and is recommended for items that are going to be cared for.

Add to cart Details Quick View
Chestnut Burnishing Cream 500ml

£16.95

This creamy liquid has a very mild abrasive within it which acts like ‘liquid sandpaper’ on finished surfaces, cutting back and cleaning the finish and elevating it to a glossier, brighter finish. It can be used to smooth Cellulose Sanding Sealer prior to applying wax or Friction Polish, or, after allowing a suitable time to dry, on any of the lacquers, Friction Polish, Finishing Oil or Hard Wax Oil. A deep finish can be achieved using Burnishing Cream on a coat of Melamine Lacquer, then a coat of Friction Polish and finally the Burnishing Cream again. Use it sparingly so as not to over lubricate the surface and be sure to shake the bottle before use. It is not advisable to use a lacquer on top of a surface that has had Burnishing Cream used on it.

Add to cart Details Quick View
Chestnut WoodWax22 450ml

£12.74

WoodWax 22 contains beeswax (for shine) and carnauba wax (for hardness). Blended together in a solvent to produce a soft creamy paste. This makes it very easy to apply over any surface. WoodWax 22 is quick drying enough to be applied onto unsealed wood but works best on one of Chestnuts sanding sealers. If working on the lathe the wax should be applied with the lathe stopped. Apply using a cloth (Safety Cloth or Stockinette works well with this); the wax spreads easily over the surface, after about 20 seconds it starts to drag slightly. This means it is ready to buff up; if you haven’t covered the whole piece by then don’t worry, just take a little more wax from the tin and carry on applying, the wax won’t mind waiting! It’s best to buff WoodWax 22 as soon as you can; that way any surplus wax that might have been applied will be removed, allowing the shine to really show through. If working on the lathe Safety Cloth should be used for the buffing process and let the lathe do the work for you. Off the lathe Safety Cloth or Stockinette can be used. A second or even third coat of wax can be applied if required, leaving about twenty minutes between coats. After three coats the finish can become softer and will mark very easily.

Add to cart Details Quick View
Chestnut Liming Wax

£11.22 – £14.92

The white pigment in Liming Wax is Titanium Dioxide (TiO2) which gives it a brilliant white finish which will perfectly highlight open grain. Use Liming Wax on any open grained timber for a dramatic and striking effect which can be emphasised by using a stain or Ebonising Lacquer first. For an even better result use the Liming Brush first to open up the grain, allowing more Liming Wax to enter; spread the Liming Wax over the whole surface and then wipe off after a few minutes. The Liming Wax will stay in the open grain and the effect will be instantly visible. Whilst Liming Wax is a wax (obviously!), the wax is mainly a carrier for the white pigment. Therefore an overcoat of some kind is needed. WoodWax 22, Microcrystalline Wax, Finishing Oil or Hard Wax Oil are ideal for this and will lock the wax in place whilst keeping it clean and bright.

Select options Details Quick View
Chestnut Cut ‘n’ Polish

£12.74

Cut’n’Polish is a blend of two waxes with a fine abrasive held in suspension within them. This is a soft wax designed to stay ‘wet’ slightly longer during application, allowing it to lubricate the abrasive to give a very fine cut to the timber and also to collect any dust generated during use and some subsequent sanding, preventing it from entering the workshop atmosphere. On bare wood; sand to 240 grit as normal, apply a coat of Cut’n’Polish with the lathe stopped, then switch on the lathe and buff to a soft sheen whilst smoothing the timber at the same time. On sealed wood apply after the sealer in the same way, polishing to a slightly higher shine. Cut’n’Polish dries almost immediately and can be overcoated with Friction Polish or any Chestnut waxes for a higher shine.

Add to cart Details Quick View
Chestnut Microcrystalline Wax 225ml

£14.19

Chestnut Products’ Microcrystalline Wax is a blend of high quality waxes rich in microcrystalline wax – a wax derived from the petroleum refining process and known for the fineness of its crystals. This is mixed with a special solvent to create a firm wax which, when dry, knits down to form a very dense coating making it very water resistant, meaning that it is ideal for any items that are likely to come into contact with water for short periods of time. Microcrystalline waxes also have a higher melting point than other waxes traditionally used to make polishing waxes, the benefit of which is that repeated handling of items finished in Microcrystalline Wax won’t finger mark in the same way, as the melting point is higher than normal body temperature. Microcrystalline Wax should be used over one of the Chestnut Products’ sanding sealers and allowed to dry (about 20 minutes) before buffing to a shine. For best results apply a very thin coat, spreading the wax evenly over the entire surface. Microcrystalline Wax can also be used on the buffing wheel system. In this situation use the A and B Wheel as normal, then apply the Microcrystalline Wax to the item you are polishing. Allow 20 minutes for the wax to dry then buff and normal using the C Wheel. You can use the same C Wheel for both Microcrystalline Wax and the Carnuaba Wax Stick. Microcrystalline Wax has been tested to the EN71 Part 3 regulations regarding coatings used on toys.

Add to cart Details Quick View
Chestnut Acrylic Sanding Sealer 400ml aerosol

£10.10

It’s important to use a sanding sealer on most items; it gives a good foundation to your piece and can help the next coat to adhere properly to the timber. Chestnut Acrylic Sanding Sealer does this perfectly and is designed to be used with Acrylic Gloss Lacquer, Acrylic Satin Lacquer, Ebonising Lacquer, any of their polishes and any of their waxes. Supplied in an easy to use aerosol the dried coating complies with the EN71 Part 3 regulations governing toys and nursery furniture. Once dried lightly sand back prior to applying your top coat.

Add to cart Details Quick View
Chestnut Cellulose Sanding Sealer 400ml aerosol

£11.22

Getting a good base for your finishing is essential when you want to get a great finish. Sometimes the piece you’re working on makes that more difficult due to its shape or size or for many other reasons. Or sometimes you just want a quicker, cleaner method of applying a sealer. That’s where Cellulose Sanding Sealer in an aerosol comes into its own. Basically the same product as in the tin, it has all the same benefits of quick drying and universal compatibility, it also has the added advantage of being easier both to apply and to get an even coating. Use it before applying waxes, lacquers and polishes for a more durable final finish.

Add to cart Details Quick View
Chestnut Acrylic Gloss Lacquer 400ml aerosol

£10.10

If you don’t have access to spraying equipment, this aerosol lacquer will give you a great finish quickly and easily. A spray application is particularly relevant when trying to achieve the best gloss finish possible. Acrylic Gloss Lacquer is a high build water based lacquer specially adapted to give the best delivery through the nozzle (chosen to give excellent results without spitting, spotting or clogging in normal use) without, of course, the use of CFCs. The lacquer itself dries quickly to give a high gloss finish straight from the can which has the benefit of being extremely hard wearing and durable – so much so that it can be used on items that will be kept outdoors or used in areas where moisture could damage other finishes. Acrylic Gloss Lacquer is touch dry and tack free in around five minutes and hard dry in twenty minutes, ready for a second coat if needed after a light rubdown with a fine abrasive. The sheen level can be increased if required by using Burnishing Cream (which will not affect the durability) or, after allowing 24 hours to ensure it is completely hard dry, by using it in conjunction with the Buffing Wheel Kit.

Add to cart Details Quick View
Chestnut Acrylic Satin Lacquer 400ml aerosol

£10.10

When you need to protect your work but don’t want an overpowering shine on it, Acrylic Satin Lacquer is an ideal choice. With the benefit of an easy aerosol application, especially useful on awkward shapes, this is a hard wearing water based lacquer that will protect whatever it’s put onto, leaving an attractive satin sheen. Acrylic Satin Lacquer is touch dry and dust free in about five minutes and hard dry about 20 minutes, ready for a second coat if needed after a light cut back with a fine abrasive. For best results it should be used over either Cellulose Sanding Sealer or the Acrylic Sanding Sealer aerosol. If you have a change of heart on the finish the lacquer can be brought to a gloss by using either Burnishing Cream or the Buffing Wheel Kit. Or you can simply apply a coat of Acrylic Gloss Lacquer!

Add to cart Details Quick View
Chestnut Ebonising Lacquer 400ml aerosol

£10.10

Ebonising Lacquer is a tough, hard-wearing water-based lacquer. It is heavily pigmented so that when it is dry it emulates the classic satin look of ebony. Usually applied over a sanding sealer (either Cellulose Sanding Sealer or Acrylic Sanding Sealer aerosol) it is touch dry in about five minutes and hard dry after twenty minutes. Although heavily pigmented it is not paint and will still allow the grain of the timber to show through, rather than obliterating it completely. Liming Wax and Gilt Cream can be applied over Ebonising Lacquer to give a pleasing, eye-catching yet very simple artistic effect. If a bright gloss finish is required from Ebonising Lacquer this is best achieved by using Burnishing Cream on the lacquer with will polish it up to a high gloss. Acrylic Gloss Lacquer can also be applied on top of Ebonising Lacquer, as can WoodWax 22 and Microcrystalline Wax.

Add to cart Details Quick View
Chestnut Melamine Gloss Lacquer 400ml aerosol

£11.22

Melamine Lacquer can be a bit fiddly to apply and there’s no better way than spraying it. If you don’t have access to spray equipment then this aerosol version is the ideal way. Melamine Gloss Lacquer will quickly build to a bright gloss finish and dries in a matter of minutes. Touch dry and safe to handle within five minutes the lacquer chemically cures to give a tougher finish. The lacquer achieves practically all of this (about 90%) within seven days, after which the process slows and can take up to another two weeks to fully complete. Best used over a Cellulose Sanding Sealer (brushing or aerosol) and can be overcoated with a wax for a softer tactile feel.

Add to cart Details Quick View
Chestnut Spirit Stain Sample Kit Rainbow Colours

£23.83

The ideal way to experiment with the different colours available to decide which ones you prefer, the Spirit Stain Kit contains one bottle (min. contents 25ml) of each of the nine colours. These are exactly the same stain as in the bigger bottles and will intermix if you want to vary the shades available.
The stains are very fade resistant, quick drying and non-grain raising.

Add to cart Details Quick View
Chestnut Spirit Stain Sample Kit Wood Colours

£23.83

The ideal way to experiment with the different colours available to decide which ones you prefer, the Spirit Stain Kit contains one bottle (min. contents 25ml) of each of the twelve wood colours. These are exactly the same stain as in the bigger bottles and will intermix if you want to vary the shades available. The stains are very fade resistant, quick drying and non-grain raising.

Add to cart Details Quick View
Chestnut Spirit Stain – 250ml

£9.70 – £11.22

An exciting and vibrant set of colours for staining wood, Spirit Stains are methanol based to make them quick drying and because of this they also will not raise the grain of the timber they are applied to. The pigments used to make this stains are of the highest quality and all score the top ratings of 7s and 8s in the Blue Wool Scale, the measuring system used to rate fade resistance. This means you can use them with confidence knowing that the colour you apply will still be the same many years later. Spirit Stains are fully inter-mixable so you can produce virtually any colour you can think of, giving you full opportunity to be as creative as you wish. The colours will also mix after application so you can blend from one colour to another for fantastic ‘flare’ effects. Spirit Stain White is designed primarily as a mixer to create pastel shades when mixed with other Spirit Stain colours. It can be used to stain timber but as it is a translucent stain this can have a limited effect depending on the base colour of the timber used. Should you want a more subtle colour you can dilute the stains with Spirit Thinners for a delicate wash effect.

Select options Details Quick View
Chestnut Gilt cream – 30ml

£13.40
Gilt Creams are a creamy, waxy paste with metallic flakes and pigments in them, giving a rich, lustrous finish to whatever they are applied to. The can be used for a ‘limed’ effect over a lacquer to give a high contrast effect, or uniformly over a piece and polished to a bright shine once dried. Available in

Gold

Silver

Copper
Select options Details Quick View
Mylands Cellulose Sanding Sealer 500ml

£13.60

Use as a wipe on sealer (2 coats) prior to applying High Build Friction polish or Melamine Lacquer. Very quick drying (3-6 minutes).

Add to cart Details Quick View
Mylands Black Polish 500ml

£19.95

Although French polish is the general term for all types of Shellac Polish, it is also a product in its own right. Mylands range contains many blends of Shellac Polish which have been developed over the years to fulfil various different requirements – some of which are slightly modified products for a specific purpose. They come in various depths of colour, which give the French Polisher latitude to choose the most appropriate product for the timber being polished. Shellac products have a variety of uses from finishing antiques and reproduction furniture to acting as a barrier between two normally incompatible finishes. They are particularly useful when refurbishing furniture as they will seal in any wax product which may have been applied to the furniture in the past.

Add to cart Details Quick View
Mylands Lacacote Wood Sanding Sealer

£19.62

Shellac Sealers are used in the French polishing trade either; as a quick drying finish to seal timber after staining; or as a basecoat for subsequent coats of French Polish.

Select options Details Quick View
Mylands Methalyted Spirits 500ml

£9.90

Used for diluting French polish, Light Fast and Earth Stains, or cleaning surfaces and tools.

Add to cart Details Quick View
Mylands High Build Friction Polish 500ml

£19.62

Sold world-wide as probably the market leader in Friction polish. After sanding surface very smooth, seal with either Cellulose Sanding Sealer or Lacacote Wood Sanding Sealer (wiped on).

Add to cart Details Quick View
Mylands Clear Wax 400g

£11.34

Mylands wax polishes are manufactured from the finest natural ingredients including pure Beeswax and Carnuba wax. Mylands wax will help hide any surface scratches and produce a deep traditional sheen. On polished surfaces use sparingly and buff within a couple of minutes.

Add to cart Details Quick View
Mylands Danish Oil 500ml

£12.80

Danish Oil is a specially formulated blend of natural and synthetic oils for use on wood products. A very durable penetrating oil suitable for both interior and exterior wood. Excellent heat and water resistance make this a very versatile finishing product.

Add to cart Details Quick View
Organoil Garden Furniture Oil

£18.95 – £31.95

A low sheen finishing oil based on Tung Nut Oil, Beeswax, Citrus solvents and anti-fungal oils that penetrates the timber substrate to nourish, preserve and seal; as well as providing protection against weather degradation and rot. A natural alternative to petroleum hydrocarbons and water based oils

Select options Details Quick View
Organoil Wax & Polish 500g

£14.95

A refined Beeswax and Citrus Oil polish with pleasant aromatics and emulsified into a ready-to-use paste. For the palest, brightest cabinetry finish offered in our range; a double wax application and polish (min. 24 hours apart) to raw, fine-sanded woodwork would be recommended.

Add to cart Details Quick View
Organoil Olde Style Danish Oil

£18.95 – £31.95

A penetrative, nourishing, quality finishing oil which reflects the original, heavy-oil formulations that traditional Danish Oils were renowned for. As a clear finish will richly enhance the existing woodcolour/s. For best results, requires quality dry-sand surface preparation; using 600 /1200 / 1500 grit papers (the finer the better) Upon curing/drying (min. 14 days) makes for ideally prepared surface for further (optional) Waxing/Polishing.

Select options Details Quick View
Organoil Hi-Speed Finishing Oil – 500ml

£18.95

Organoils Hi-Speed Finishing Oils specifically formulated for on-lathe, under-turning-speed finishing. It is a heavy oil which can well deal with the load (fill) requirements of softwoods - you may choose to cut it (with vegetable turpentine) for denser hardwoods. One of its unique ingredients is the rare, Mustard Seed Oil (a well kept Aussie secret until now!) which gives the formulation good slip for the wet-sanding procedure and a silken touch to the finished result.

Add to cart Details Quick View
U-Beaut Aussie Oil 250ml

£23.60

This is an oil type finish similar to Danish oil but nothing like it. This product is designed to be hand rubbed on to raw timber, giving a finish with a hard, bright, high gloss. It will bring out amazing depth and brilliance to most timbers making the grain pop and become opalescent, vibrant, shimmering and alive. Especially when used on a fine grained, highly figure timber. And if that's not enough it does it all in a matter of minutes.

Aussie Oil is ideal for use on most small items like pendants, brooches, earrings, small turned items that cannot be fully finished on the lathe. Pens, magnifying glass handles, compacts, key rings, letter openers, in fact almost anything made of wood you can comfortably hold in your hand to polish.

As an extra added bonus, it also works brilliantly as a friction polish on the lathe.

Add to cart Details Quick View
U-Beaut Shellawax Liquid 250ml

£23.60

A one-application woodturners friction polish that really does work and is ideal for use on smaller spindle work such as pens and similar objects up to around 10 cm (4") diameter. This exceptional polish is made using a specially formulated hard shellac as a base to give a harder, more durable finish, giving greater resistance to marks and blemishes from water, alcohol and heat. Normally applied directly onto bare timber (though it can be used over most oils too – but test on scrap first) this polish dries almost instantly yet goes on hardening for up to three weeks resulting in a truly durable finish which far exceeds others on the market today. Once fully cured the finish is food-safe and non-toxic.

Add to cart Details Quick View
U-Beaut Shellawax Cream 250ml

£23.60

Shellawax cream is a woodturners friction and buffing polish. Sharing many of the characteristics of Shellawax liquid, Shellawax Cream is specially formulated for use on larger turned projects where it would normally be impossible to get a first class finish using a conventional friction polish and on stand-alone articles such as carvings. As with Shellawax, only one application is required to completely finish the work. Made using a specially formulated hard shellac as a base, this excellent product gives a hard, durable finish, with impressive resistance to marks and blemishes from water, alcohol and heat. The cream formulation retards the frictional drying characteristic of friction polishes, making it suitable for use on larger lathe-turned items such as bowls and platters. Being a cream, this product is easily controlled in application and is very economical in use. Shellawax Cream is non-toxic.

Add to cart Details Quick View
Out of stock

U-Beaut Shellawax Glow 500ml

£34.25

Shellawax Glow is darker than regular Shellawax (a deep honey to tan colour). It is made from a special blend of shellacs and is designed to give more depth and richness to highly figured timbers like fiddleback, birdseye, flame and quilted woods. It will also give more richness and a sense of depth to many other timbers.

Shellawax Glow is identical in use and all other respects to regular Shellawax. It is applied in the same way and has all the same properties. It can also be mixed with Shellawax Cream as an extender and thinner and can be used over EEE-Ultra Shine.

This polish may darken white woods ever so slightly, so it is a good idea to try it on a scrap piece first to make sure it doesn't darken more than you want.

USING SHELLAWAX CREAM AS A SHELLAWAX GLOW EXTENDER Shellawax Glow can be mixed with Shellawax Cream as an extender. This allows for better use of these products on large turned work and for hand rubbed work. For bowls over (6”) 150mm diam, mix the Cream and Shellawax Glow at the rate of approx 50/50 this will give you a runny cream that will stay on the surface longer and allow you more time to work it into the timber.

Use different mixing rates for various jobs 20% Cream to 80% Shellawax Glow for large platters etc up to 900mm (3’) diam and larger.

SHELLAWAX GLOW AS A THINNER Use Shellawax as a thinner for Shellawax Cream, which often thickens with use. This will also extend the life of the Cream. The slight colour difference will not effect the colour of Cream when used.

Details Quick View
U-Beaut Sanding Sealer 500ml

£16.00

This sanding sealer is designed to raise the grain and make it brittle, it can then be sanded of with fine grit abrasive paper leaving a smooth fine surface to apply finish.

Add to cart Details Quick View
U-Beaut EEE-Ultra Shine 250ml

£18.65

This amazing product is a cut and polish paste containing Tripoli powder, an ultra-fine abrasive. The polish is designed to be used in conjunction with Shellawax Cream and liquid formulations or as a finish in its own right on plastics (such as acrylic, resin-impregnated burr, crushed velvet, artificial ivory and similar products used for pen bodies). It can also be used after French polishing and restorers will find it useful to cut and revive previously polished surfaces. Although designed to be used directly on raw timber, bear in mind that EEE is not a finish in itself and the polished surface will need protecting by the use of some other product (such as Shellawax). EEE-Ultra Shine can be used over many other finishes such as oils and most types of varnish, enhancing the surface and giving it a smoothness and lustre with an ease that you would never have thought possible.

Add to cart Details Quick View
U-Beaut Hard Shellac 500ml

£29.50

Ever wished you had a finish that was as easy to use as shellac but with the durability of polyurethane? Well wish no more, because here it is.

This unique Hardened Shellac creates a film with a high resistance to heat, water and alcohol, yet it is used in exactly the same was as any normal shellac. It can be applied with a rubber as French polish, brushed, sprayed and dipped.

HOW IS THIS POSSIBLE? After shellac has been dissolved in ethanol* it is possible to introduce additives that cause the shellac to cross link after it has dried. This cross linking takes about 20 days to completely cure, less in hot weather.

USES: Ideal for table tops and other horizontal surfaces such as dresser and desk tops, etc. Also brilliant for use on guitars, lutes, harps and many other musical instruments where a traditional finish is required and good resonance qualities are essential.

NEW IMPROVED FORMULA In February 2009 U-beaut began adding a plasticiser to Hard Shellac. This gives elasticity to the cured finish, to combat crazing on the thin walls of musical instruments, whilst still having the same high resistance to marking from water, alcohol and heat it has always had.

Add to cart Details Quick View
Rustins Plastic Coating Thinners

£6.45 – £12.75

Removal of Plastic Coating from brushes, rollers and application equipment. Also used to thin Plastic Coating when necessary if it is to be sprayed. Also used to thin the product when an opened grained oil type finish is required.

Select options Details Quick View
Rustins Danish Oil

£7.37 – £12.48

A unique formulation developed by Rustins that is suitable for all types of wood. It differs from Teak Oil in that it contains special ingredients to give it a low lustre finish. It is an easy to use wipe on finish, which brings out the beauty of the timber and gives a natural, open grained, soft lustrous finish. Ideal for all woods and is excellent on turned woodwork. Danish Oil conforms to The Articles in Contact with Food Regulations and to the Toys (Safety) Regulations 1995, BS:EN71 Part 3.

Select options Details Quick View
Rustins Plastic Coating & Hardener Gloss

£28.55

Two-part clear cold cure lacquer for use on wood, hardboard, cork and plastic laminates. Extremely good adhesion, resistant to heat, solvents and abrasion. Can be burnished to a mirror like gloss or rubbed down to a smooth, satin finish with steel wool and wax. An excellent finish for marquetry as it does not darken light coloured veneers and does not yellow or craze on ageing. Hard-dry within 2 hours of application. Plastic Coating conforms to The Articles in Contact with Food Regulations.

Add to cart Details Quick View
Briwax Clear wax Polish – 400grm

£17.00

Briwax Original is formulated with fast drying, stronger solvents which speed up drying, and also increase the cleaning ability of the wax slightly. This means that it will renovate older dirtier furniture and leave you with the deep grain enriching Briwax shine. Unsealed wooden surfaces should be smooth, dry and clean. Apply Briwax using a lint free cloth or 0000 Steel Wool, thoroughly working the wax into the grain. Once dry, buff to desired finish with a clean soft cloth.

Add to cart Details Quick View
Liberon Verdigris Wax 250ml

£18.75

Verdigris Wax is a multi-purpose coloured wax for creating striking effects on all types of interior material such as wood, metal, stone, plastic and plaster. Recommended as a special effects wax, it gives green hues of oxidised copper and brass and can be worked into moulding, bronzes, papier-mâché, alabaster and carvings. Ideal for decorating household objects, it buffs to a soft sheen, and can also be applied as a wax finish to bare or coloured wood.

Add to cart Details Quick View
Liberon Superior Danish Oil with UV filter 250ml

£7.75

Liberon Superior Danish Oil is a blend of pure, high quality tung oil and natural oils that feed, enhance and protect hard and soft woods. It is a penetrating oil, which brings out the natural grain of the timber and provides a satin to gloss sheen. With added UV filters to help prevent discolouration from the sun, and water, heat and alcohol resistant, it is suitable for both interior and exterior use. It is safe for use on toys.

Add to cart Details Quick View
Liberon Quick Drying Tung Oil 250ml

£12.25

Liberon Quick Drying Tung Oil is a high quality natural oil for protecting interior and exterior wood. It provides a hard-wearing finish, and is ideal for surfaces such as tables and furniture. A quicker drying version of Liberon Pure Tung Oil, each coat dries in approximately four hours, and is highly resistant to water, alcohol and food acids. Being a penetrating oil it allows the wood to age gracefully and develop a natural patina. It provides a long-lasting matt finish.

Add to cart Details Quick View
Hampshire Sheen – Lacquer 500ml Aerosol

£10.50

Hampshire Sheen - Lacquer 500ml Aerosol have been formulated to be strong, flexible and very glossy. They can be used for both internal and external projects. Glass like finishes can be achieved with these two superb acrylic spray lacquer products. Supplied in 500ml cans with 2 nozzles.

Select options Details Quick View
Hampshire Sheen – 400ml Sprays

£12.65 – £13.19
Professional Clear Gloss Lacquer Superb thick, nicely levelling product. Requires fewer coats for a deep, lush shine. Can be mechanically buffed after a few hours.

Professional Clear Satin Lacquer Produces a superb satin finish on most surfaces in just two coats (over sealer) without further work required.

Professional Black Gloss Lacquer Like the Clear Gloss, this black requires fewer coats for a fantastic depth of finish.

Professional Black Satin Lacquer A silky smooth black surface over sealer can be produced in just a couple of coats. Use without sealer to preserve visible grain.

5. Professional Matt Sanding Sealer An excellent spray-on sealer with plenty of solids providing a super-hard surface for any finish to be applied over the top.
Select options Details Quick View
Hampshire Sheen – high gloss 130g

£14.29

As the name suggests, the High Gloss variation brings a higher shine to your decorative woodwork . It is tough, with an additional 'Pow' of shine that suits some lathe projects. Contains a high quantity of carnauba and microcrystalline waxes. Shiny, tough and exceptionally long lasting. Food and toy safe, too. Supplied in 130g tins.

Add to cart Details Quick View
Hampshire Sheen – microcrystalline wax 130g

£11.55

Quick drying Microcrystalline Wax is an ideal protective finish for many different projects and has many uses besides wood. Both Fingerprint and water resistant, Microcrystalline Wax is a hard wearing overcoat to wax and other finishes for an extra level of gloss and protection to your decorative wood items. Just a little of the product goes a very long way, so use it sparingly!

Add to cart Details Quick View
Hampshire Sheen Embellishing Wax

£13.99

Hampshire Sheen embellishing wax is designed to be used on open grain woods such as oak or ash and works brilliantly to highlight textured elements on tighter grained woods. Use in conjunction with the Intrinsic Colour Collection for stunning results. Supplied in a 130g lever lid tin. Apply liberally and buff to a gloss.

Select options Details Quick View
Hampshire Sheen Embellishing Wax

£7.25

Hampshire Sheen Embellishing Wax are ideal for enhancing open grained decorative items from woods such as Oak or Ash or woods with added texture. They work brilliantly in combination with the Intrinsic Colour Collection and this selection available in nine colours are a great, easy to apply alternative to gilt creams. Supplied in 60g tins.

Select options Details Quick View
Hampshire Sheen – Cellulose Sanding Sealer 500ml

£13.75

Hampshire Sheen - Cellulose Sanding Sealer 500ml is pre-thinned, giving you absolute control of the provided surface. Supplied in 500ml tin.

Add to cart Details Quick View
Hampshire Sheen – Food and Toy Safe Danish Oil 500ml

£11.55

Hampshire Sheen’s Danish Oil is food contact and toy safe when fully cured and complies to EU71 regulation. Thinner, more penetrating and less smelly that other Danish Oils, this product contains only pure Tung Oil and no artificial varnish, resins or other vegetable oils.

Add to cart Details Quick View
Hampshire Sheen – Citrus Burnishing Oil 500ml

£14.29

Citrus Burnishing oil can be easily applied and then burnished dry in a matter of minutes, and can be overcoated with waxes or lacquers if you wish. Use multiple coats for a water and oil resistant finish suitable for salad, fruit and snack bowls. Easy to apply; Over 50% Tung Oil; Food Safe when dry; Fresh smell when dry, fading over time; Deeply penetrating and protecting; Will not chip, flake or peel; Naturally water and oil resistant when cured. Supplied in a 500ml (17.6oz) cone top bottle.

Add to cart Details Quick View

Title