-
Perforated design which allows the dust to escape without clogging. -
2" wide cloth backed abrasive available in six grits, 80G, 120G, 180G, 240G, 320G & 400G. -
2" wide cloth backed abrasive available in six grits, 80G, 120G, 180G, 240G, 320G & 400G.
-
2" velcro (hook and loop ) backed abrasive sanding discs. Designed to be used in a power drill but can also be used in the Robert Sorby Sandmaster. Available in 60G, 80G, 120G, 180G, 240G, 320G & 400G. -
Velcro backed 6" (150mm) wide rolls x 1 metre in 9 grits, 80G, 120G, 180G, 240G, 320G, 400G, 600G, 800G & 1200G -
3" velcro (hook and loop ) backed abrasive sanding discs. Designed to be used in a power drill. Available in 80G, 120G, 180G, 240G, 320G & 400G. -
Perforated design which allows the dust to escape without clogging. mixed pack of 15, 3 of each of the following 5 grits, 120G, 180G, 240G, 320G 400G, 70mm x 125mm.
-
Fine finish starts with good preparation! Use these mildly abrasive pads after sanding for a final smoothing process to give a near-perfect surface prior to applying any finish. Very long lasting, these pads are also very flexible and do not crumble, thus avoiding contamination of your work. -
2" Soft density tapered arbor for external and shallow internal curves Accepts all Velcro/loop backed abrasives including self or pre-cut squares and discs.- colour may vary
-
Fine finishing starts with good preparation! Use these mildly abrasive pads after sanding for that final smoothing process to give a near-perfect surface prior to applying any finish. Very long lasting, these pads are also very flexible and do not crumble, thus avoiding any fear of contamination of your work. Exercise care when using these pads with the lathe revolving.
-
Velcro backed 6" (150mm) wide rolls x 1/2 metre of each of the following grits: 120G, 180G, 240G, 320G, 400G & 600G
-
2" arbors 50mm x 6mm spindle pad with a 20mm foam, soft pad for external and shallow curves . Accepts all Velcro/loop backed abrasives including self or pre-cut squares and discs.- colour may vary
-
3" arbors 75mm x 6mm spindle pad with 20mm foam -
1" x 20' abrasive in a convenient dispenser. Perfect for spindle, pen, or any turning where small strips are needed. This convenient dispenser is loaded with four or 1" x 20' rolls of cloth backed aluminum oxide abrasive. Each dispenser pack contains one roll of 150, 240, 320 & 400 grit abrasive. Just pull out and tear off the length of abrasive strip you need. -
1" x 20' abrasive in a convenient dispenser. Perfect for spindle, pen, or any turning where small strips are needed. This convenient dispenser is loaded with five 1" x 20' rolls of cloth backed aluminum oxide abrasive. Each dispenser pack contains one roll of 150, 240, 320, 400 & 600 grit abrasive. Just pull out and tear off the length of abrasive strip you need. -
2" velcro backed abrasive sanding discs & arbors, includes 6 x 47 arbors. 4 Spare pads (2 soft red, 2 normal). 20 each x 50mm indasa Velcro discs in grits, 120,180,240,320,400 & 600G -
Out of stock
Includes 1 x 72 arbor. Spare pads. 20 each x 75mm indasa Velcro discs in grits, 120,180,240,320,400 & 600G -
If you don’t have access to spraying equipment, this aerosol lacquer will give you a great finish quickly and easily. A spray application is particularly relevant when trying to achieve the best gloss finish possible. Acrylic Gloss Lacquer is a high build water based lacquer specially adapted to give the best delivery through the nozzle (chosen to give excellent results without spitting, spotting or clogging in normal use) without, of course, the use of CFCs.
The lacquer itself dries quickly to give a high gloss finish straight from the can which has the benefit of being extremely hard wearing and durable – so much so that it can be used on items that will be kept outdoors or used in areas where moisture could damage other finishes.
Acrylic Gloss Lacquer is touch dry and tack free in around five minutes and hard dry in twenty minutes, ready for a second coat if needed after a light rubdown with a fine abrasive.
The sheen level can be increased if required by using Burnishing Cream (which will not affect the durability) or, after allowing 24 hours to ensure it is completely hard dry, by using it in conjunction with the Buffing Wheel Kit.
-
If you need to get away from the smell and flammability of our cellulose based lacquers this is an ideal option.
This water based lacquer has virtually no smell and is totally non-flammable. Don’t be fooled though, this product is extremely hard wearing and gives a full gloss finish.
Being water based it is slightly slower drying, taking about twenty minutes to be touch dry. If you want to apply a second coat it should be left two hours before doing so, although a wax can be applied if required after about thirty minutes.
This product can be sprayed if suitable equipment is available, or can be applied by cloth or brush. We recommend foam brushes for application as this keeps the foaming action of acrylics to a minimum.
-
It’s important to use a sanding sealer on most items; it gives a good foundation to your piece and can help the next coat to adhere properly to the timber.
Chestnut Acrylic Sanding Sealer does this perfectly and is designed to be used with Acrylic Gloss Lacquer, Acrylic Satin Lacquer, Ebonising Lacquer, any of their polishes and any of their waxes.
Supplied in an easy to use aerosol the dried coating complies with the EN71 Part 3 regulations governing toys and nursery furniture.
Once dried lightly sand back prior to applying your top coat.
-
This water based sanding sealer gets the job done without the smell associated with solvent based sealers and also with no flammability issues – ideal for asthma suffers and anyone with an aversion to solvent based finishes.
Applied by cloth, brush or spray (Chestnuts' foam brushes are especially good with this) the sealer dries in about 5 minutes and can be overcoated with most compatible finishes after about 20 minutes although two hours should be left if using Acrylic Lacquer.
Acrylic Sanding Sealer sands easily with a fine abrasive and is supplied ready for use.
-
When you need to protect your work but don’t want an overpowering shine on it, Acrylic Satin Lacquer is an ideal choice. With the benefit of an easy aerosol application, especially useful on awkward shapes, this is a hard wearing water based lacquer that will protect whatever it’s put onto, leaving an attractive satin sheen.
Acrylic Satin Lacquer is touch dry and dust free in about five minutes and hard dry about 20 minutes, ready for a second coat if needed after a light cut back with a fine abrasive.
For best results it should be used over either Cellulose Sanding Sealer or the Acrylic Sanding Sealer aerosol.
If you have a change of heart on the finish the lacquer can be brought to a gloss by using either Burnishing Cream or the Buffing Wheel Kit. Or you can simply apply a coat of Acrylic Gloss Lacquer!
-
Briwax Original is formulated with fast drying, stronger solvents which speed up drying, and also increase the cleaning ability of the wax slightly. This means that it will renovate older dirtier furniture and leave you with the deep grain enriching Briwax shine. Unsealed wooden surfaces should be smooth, dry and clean. Apply Briwax using a lint free cloth or 0000 Steel Wool, thoroughly working the wax into the grain. Once dry, buff to desired finish with a clean soft cloth. -
This kit gets you started on the road to buffing – all you need to supply is the lathe, a chuck and something to buff! Inside the kit you get the mandrels for holding the Buffing Wheels in the chuck. One of each buffing wheel (A, B and C) are included in the 8 inch size, complete with all the fixings attached to fit into the Mandrels. A bar of each of the compounds is included to get you started, these will last a long time so no need to worry about getting spares yet (although all of the items in the kit are available separately when you need to get them). Next is a stick of carnauba wax for that final gloss finish. Last but not least is a full set of instructions on how to use the kit to get the best from it. -
This creamy liquid has a very mild abrasive within it which acts like ‘liquid sandpaper’ on finished surfaces, cutting back and cleaning the finish and elevating it to a glossier, brighter finish. It can be used to smooth Cellulose Sanding Sealer prior to applying wax or Friction Polish, or, after allowing a suitable time to dry, on any of the lacquers, Friction Polish, Finishing Oil or Hard Wax Oil. A deep finish can be achieved using Burnishing Cream on a coat of Melamine Lacquer, then a coat of Friction Polish and finally the Burnishing Cream again. Use it sparingly so as not to over lubricate the surface and be sure to shake the bottle before use. It is not advisable to use a lacquer on top of a surface that has had Burnishing Cream used on it. -
This is a solid block of carnauba wax, popular with woodturners. It gives a bright gloss finish and is also very hard wearing, able to withstand a medium amount of handling without showing finger marks. Apply over a sanding sealer by holding it against your work at it revolves on the lathe. Do not press too much – the wax is very hard and can scratch softer woods – the idea is to generate enough heat for the wax to melt slightly and transfer onto the wood. (This is easier than it sounds!). Use sparingly, and use the polishing process (using safety cloth) to ensure the wax is spread evenly. Buffing will produce a high gloss finish. -
Getting a good base for your finishing is essential when you want to get a great finish. Sometimes the piece you’re working on makes that more difficult due to its shape or size or for many other reasons.
Or sometimes you just want a quicker, cleaner method of applying a sealer.
That’s where Cellulose Sanding Sealer in an aerosol comes into its own. Basically the same product as in the tin, it has all the same benefits of quick drying and universal compatibility, it also has the added advantage of being easier both to apply and to get an even coating.
Use it before applying waxes, lacquers and polishes for a more durable final finish.
-
Good finishing requires a good foundation, and Cellulose Sanding Sealer is probably the best way of providing one. Compatible with everything in the Chestnut Products range that benefits from the use of a sanding sealer (which is pretty much everything apart from oil finishes!) it is superbly universal.
The purpose of a sanding sealer is manifold.
- It seals the open pores of the timber prior to the application of the next coat, meaning that more of it stays on the surface and less of the finish is needed. Not only does this make it economical, when finishing the thinner the applied coat the less likely it is to get damaged, so a sanding sealer will help the top coats be more resilient.
- Sanding Sealers also bind the loose fibres of the timber together giving a more solid foundation for the next coat, which helps make sure the final finish is able to adhere properly and thus be more durable.
- They also include a sanding agent which acts as a lubricant to make the sanding process easier – the sanding agent also stands slightly proud of the surface of the sealer and it is this that is denibbed – the sealer itself should still be intact after sanding.
-
Use as a wipe on sealer (2 coats) prior to applying High Build Friction polish or Melamine Lacquer. Very quick drying (3-6 minutes). -
This pure cellulose solvent is a high quality dilutant for our cellulose based products, such as Cellulose Sanding Sealer and Melamine Lacquer. Thinning these products can help to make them easier to apply, especially over larger areas as it helps them flow out. Cellulose Thinners is also useful for cleaning any spills you may have in the workshop and is strong enough to help clean most things, taking care to ensure that it does not attack It can also be used to thin Spirit Stain to give a delicate wash effects, although spirit thinners is the better option for this. -
These compounds are designed to co-ordinate with the cloth used in the Buffing Wheels and Dome Buffs to give an exceptional cut and prepare the surface to a very smooth finish prior to using wax. Compound 1 -the brown one – (sometimes referred to as tripoli) is used with the ‘A’ Wheel/Dome to help smooth the applied finish. Avoid overloading the wheel/dome where possible to prevent a build up of the compound. If this happens it can be removed by either washing in soapy water or abrading the edge of the wheel with a coarse abrasive. Do not use on very open grained light coloured timber as the compound can get lodged in the grain and colour the piece. Compound 2 – the white one – (sometimes referred to as white diamond) acts as a cleanser to remove any traces of Compound 1 left on the surface (but not from the grain) and also has a very fine abrasive contained in it which smooths the work, leaving a semi-gloss finish and a superb foundation for the top coat of wax. Use Compound 2 sparingly, too much on the wheel will result in smears on the surface of your work which can be removed with buffing but this can be very time consuming and frustrating. It’s always best to apply a little and add more if needed. -
Danish Oil is a specially formulated blend of natural and synthetic oils for use on wood products. A very durable penetrating oil suitable for both interior and exterior wood. Excellent heat and water resistance make this a very versatile finishing product.
