- The Green pads are 400 grit
- The Red pads are 600 grit
- The Orange pads are 1000 grit
- The White pads do not contain an abrasive and are thus technically non-abrasive, but the very texture of the pads gives them an incredibly fine – but immeasurable – cut.
-
NyWeb pads are a non-woven nylon webbing with an abrasive – either silicon carbide or aluminium oxide – embedded into them to give an exactly defined cut. -
Liberon Finishing Oil is a blend of high quality oils for use on all interior wood and turned woodwork. Used to nourish and enhance the colour of the wood, it is suitable for use on kitchen tables and bathroom furniture, and can also be applied to cork, stone and terracotta. Water, heat, alcohol and food acid resistant, it gives a matt, satin or gloss finish depending upon the number of coats applied. Ideal for surfaces requiring a hard wearing and water-resistant finishes.
-
Ever wished you had a finish that was as easy to use as shellac but with the durability of polyurethane? Well wish no more, because here it is.
This unique Hardened Shellac creates a film with a high resistance to heat, water and alcohol, yet it is used in exactly the same was as any normal shellac. It can be applied with a rubber as French polish, brushed, sprayed and dipped.
HOW IS THIS POSSIBLE? After shellac has been dissolved in ethanol* it is possible to introduce additives that cause the shellac to cross link after it has dried. This cross linking takes about 20 days to completely cure, less in hot weather.
USES: Ideal for table tops and other horizontal surfaces such as dresser and desk tops, etc. Also brilliant for use on guitars, lutes, harps and many other musical instruments where a traditional finish is required and good resonance qualities are essential.
NEW IMPROVED FORMULA In February 2009 U-beaut began adding a plasticiser to Hard Shellac. This gives elasticity to the cured finish, to combat crazing on the thin walls of musical instruments, whilst still having the same high resistance to marking from water, alcohol and heat it has always had.
-
1" x 20' abrasive in a convenient dispenser. Perfect for spindle, pen, or any turning where small strips are needed. This convenient dispenser is loaded with four or 1" x 20' rolls of cloth backed aluminum oxide abrasive. Each dispenser pack contains one roll of 150, 240, 320 & 400 grit abrasive. Just pull out and tear off the length of abrasive strip you need. -
If you need to get away from the smell and flammability of our cellulose based lacquers this is an ideal option.
This water based lacquer has virtually no smell and is totally non-flammable. Don’t be fooled though, this product is extremely hard wearing and gives a full gloss finish.
Being water based it is slightly slower drying, taking about twenty minutes to be touch dry. If you want to apply a second coat it should be left two hours before doing so, although a wax can be applied if required after about thirty minutes.
This product can be sprayed if suitable equipment is available, or can be applied by cloth or brush. We recommend foam brushes for application as this keeps the foaming action of acrylics to a minimum.
-
This kit gets you started on the road to buffing – all you need to supply is the lathe, a chuck and something to buff! Inside the kit you get the mandrels for holding the Buffing Wheels in the chuck. One of each buffing wheel (A, B and C) are included in the 8 inch size, complete with all the fixings attached to fit into the Mandrels. A bar of each of the compounds is included to get you started, these will last a long time so no need to worry about getting spares yet (although all of the items in the kit are available separately when you need to get them). Next is a stick of carnauba wax for that final gloss finish. Last but not least is a full set of instructions on how to use the kit to get the best from it. -
Use as a wipe on sealer (2 coats) prior to applying High Build Friction polish or Melamine Lacquer. Very quick drying (3-6 minutes). -
Quick drying Microcrystalline Wax is an ideal protective finish for many different projects and has many uses besides wood. Both Fingerprint and water resistant, Microcrystalline Wax is a hard wearing overcoat to wax and other finishes for an extra level of gloss and protection to your decorative wood items. Just a little of the product goes a very long way, so use it sparingly! -
Mylands wax polishes are manufactured from the finest natural ingredients including pure Beeswax and Carnuba wax. Mylands wax will help hide any surface scratches and produce a deep traditional sheen. On polished surfaces use sparingly and buff within a couple of minutes. -
A refined Beeswax and Citrus Oil polish with pleasant aromatics and emulsified into a ready-to-use paste. For the palest, brightest cabinetry finish offered in our range; a double wax application and polish (min. 24 hours apart) to raw, fine-sanded woodwork would be recommended. -
The Sandmaster is an essential part of every turner's tool kit. It comes with 5 different grits of abrasive to take even the roughest projects to a glass-like finish every time. It avoids an uneven finish often associated with hand sanding and there is no danger of catching hands on the revolving project. There is little or no surface damage/head build-up, as there is with power sanding and there is no cable to trip over. Head articulates to access even the most difficult areas. Sponge head is ideal for working in tight spaces. Sandmaster creates a fraction of the dust generated by power sanding. It can be adapted to take a polishing mop. -
2" velcro backed abrasive sanding discs & arbors, includes 6 x 47 arbors. 4 Spare pads (2 soft red, 2 normal). 20 each x 50mm indasa Velcro discs in grits, 120,180,240,320,400 & 600G -
These Dispensing Nozzles are, in fact, almost indispensable! They fit onto any of Chestnuts' plastic bottles in the 250ml, 500ml and 1 ltr sizes, simply replacing the existing cap. Cut the tip off to the size you want and use the handy cover to reseal them when not in use. A useful by product of using these is that if you knock a bottle over the amount you lose through the small nozzle will be much less than without it. Just don’t forget to take the nozzle off the bottle before you throw it away so that you can re-use it! These nozzles are not child resistant, the correct closure should be replaced when the product is not in use. -
Gilt Creams are a creamy, waxy paste with metallic flakes and pigments in them, giving a rich, lustrous finish to whatever they are applied to. The can be used for a ‘limed’ effect over a lacquer to give a high contrast effect, or uniformly over a piece and polished to a bright shine once dried. Available in- Gold
- Silver
- Copper
-
Shellac Sanding Sealer is the traditional way of sealing timber prior to applying a polish or a wax.
Chestnuts version has a high percentage of real shellac which means it does the job extremely well, dissolved in an ethanol solution to make it easy to apply and quick drying.
Applied by cloth, brush or spray it dries in about 20 minutes, making it very popular for cabinet and architectural work as it is easy to keep a wet edge running. It is also popular with woodturners and highlights the natural grain of the timber extremely well.
Sand back lightly after application and apply Friction Polish, French Polish or any of Chestnuts waxes on top.
Conforms to EN71 Part 3 – suitable for toys and nursery furniture.
-
The ideal way to experiment with the different colours available to decide which ones you prefer, the Spirit Stain Kit contains one bottle (min. contents 25ml) of each of the nine colours. These are exactly the same stain as in the bigger bottles and will intermix if you want to vary the shades available.
The stains are very fade resistant, quick drying and non-grain raising. -
Interior use only, initial tack time 30 mins, setting time 24 hours approximately. Open time 5 minutes, assembly time 10-15 minutes, shelf life 12 months (kept airtight). -
This creamy liquid has a very mild abrasive within it which acts like ‘liquid sandpaper’ on finished surfaces, cutting back and cleaning the finish and elevating it to a glossier, brighter finish. It can be used to smooth Cellulose Sanding Sealer prior to applying wax or Friction Polish, or, after allowing a suitable time to dry, on any of the lacquers, Friction Polish, Finishing Oil or Hard Wax Oil. A deep finish can be achieved using Burnishing Cream on a coat of Melamine Lacquer, then a coat of Friction Polish and finally the Burnishing Cream again. Use it sparingly so as not to over lubricate the surface and be sure to shake the bottle before use. It is not advisable to use a lacquer on top of a surface that has had Burnishing Cream used on it. -
These compounds are designed to co-ordinate with the cloth used in the Buffing Wheels and Dome Buffs to give an exceptional cut and prepare the surface to a very smooth finish prior to using wax. Compound 1 -the brown one – (sometimes referred to as tripoli) is used with the ‘A’ Wheel/Dome to help smooth the applied finish. Avoid overloading the wheel/dome where possible to prevent a build up of the compound. If this happens it can be removed by either washing in soapy water or abrading the edge of the wheel with a coarse abrasive. Do not use on very open grained light coloured timber as the compound can get lodged in the grain and colour the piece. Compound 2 – the white one – (sometimes referred to as white diamond) acts as a cleanser to remove any traces of Compound 1 left on the surface (but not from the grain) and also has a very fine abrasive contained in it which smooths the work, leaving a semi-gloss finish and a superb foundation for the top coat of wax. Use Compound 2 sparingly, too much on the wheel will result in smears on the surface of your work which can be removed with buffing but this can be very time consuming and frustrating. It’s always best to apply a little and add more if needed. -
Tung Oil, or Chinese Wood Oil as it’s sometimes called, is a natural oil derived from the seed of the nut of the tung tree. The jury is out as to whether it can spark a nut allergy. Tung Oil air dries to form a tough, hard film that has a fairly strong amber tint. Because it doesn’t have any solvent or driers in it it can take a while to dry, and dependant on conditions this can be up to a week although 48 hours is more common. As with most finishes a thinner coat will dry quicker. Normally applied with a brush or cloth. -
Hampshire Sheen Intrinsic Colours being water based, they are non-flammable, environmentally friendly and afford you a long working time. They sink deeply into the wood and preserve the appearance of the figure in the wood, releasing the hidden subtleties. Apply more than one coat of dye to build up depth of colour, and add a black or earth undercoat for an even more dramatic effect. For the adventurous colourist, Intrinsic Colours can be mixed together to create even more shades or thinned with water for a lighter shade. -
Hampshire Sheen Pen Turners Overcoat is a 100% microcrystalline stick for pen turners who enjoy the benefits of this special wax on their turned pens, be them wood or otherwise. It applies over any finish the turner favours to give a fingerprint resistant, glossy shine. -
Liberon Black Patinating Wax is used for adding a coloured finish, highlighting areas or creating striking effects on all types of interior materials. It is ideal for ageing modern furniture, disguising repairs to old and new furniture, and highlighting areas on finished pieces and decorative carvings. It is suitable for use on wood, metal, gilt, plaster, tone, MDF and papier-mâché. -
Melamine Lacquer can be a bit fiddly to apply and there’s no better way than spraying it. If you don’t have access to spray equipment then this aerosol version is the ideal way.
Melamine Gloss Lacquer will quickly build to a bright gloss finish and dries in a matter of minutes.
Touch dry and safe to handle within five minutes the lacquer chemically cures to give a tougher finish. The lacquer achieves practically all of this (about 90%) within seven days, after which the process slows and can take up to another two weeks to fully complete.
Best used over a Cellulose Sanding Sealer (brushing or aerosol) and can be overcoated with a wax for a softer tactile feel.
-
A penetrative, nourishing, quality finishing oil which reflects the original, heavy-oil formulations that traditional Danish Oils were renowned for. As a clear finish will richly enhance the existing woodcolour/s. For best results, requires quality dry-sand surface preparation; using 600 /1200 / 1500 grit papers (the finer the better) Upon curing/drying (min. 14 days) makes for ideally prepared surface for further (optional) Waxing/Polishing. -
The finest of Steel Wool, very low crumble and virtually oil free to ensure there is no contamination of your work. Use it after sanding with abrasive sheets to give an ultra smooth surface, or to apply waxes to smooth the timber whilst applying a thin coat. Steel Wool burns very quickly and easily; keep it away from sources of combustion (i.e. sparks etc). Always use a knife or scissors to cut Steel Wool -
Designed specifically with pen turners in mind. This finishing kit consists of nine different, colour coded, foam backed sanding pads measuring 10cm (4") x 8.5cm (3.1/4"). Includes the following grit sizes: 1500 - Rust 1800 - Green 2400 - Black 3200 - Tan 3600 - Wine/Brown 4000 - Teal 6000 - Purple 8000 - Royal Blue 12000 - Grey Suitable for wood and acrylic blanks . -
Citrus Burnishing oil can be easily applied and then burnished dry in a matter of minutes, and can be overcoated with waxes or lacquers if you wish. Use multiple coats for a water and oil resistant finish suitable for salad, fruit and snack bowls. Easy to apply; Over 50% Tung Oil; Food Safe when dry; Fresh smell when dry, fading over time; Deeply penetrating and protecting; Will not chip, flake or peel; Naturally water and oil resistant when cured. Supplied in a 500ml (17.6oz) cone top bottle. -
2" Soft density tapered arbor for external and shallow internal curves Accepts all Velcro/loop backed abrasives including self or pre-cut squares and discs.- colour may vary
-
Chestnut Finishing Oil is Chestnuts' version of Danish Oil* and uses Tung Oil as its base but with the addition of solvents and driers. This aids the drying of the product and speeds it up dramatically, so that it’s dry within eight hours. It has a pale amber colour and dries to a hard yet flexible film which is very hardwearing and water resistant.
For a high gloss finish apply several coats with a light rub down between coats; after 5 or 6 coats a good sheen should be visible.
Finishing Oil is normally applied by cloth but on larger areas a brush can be used very successfully.
-
Food Safe Finish is a clear, food grade mineral oil. Chestnut use a thin grade of oil to allow it to soak into bare timber which then protects it against water splashes etc whilst not tainting or affecting the food in any way. It dries to a fairly matt finish; it is however ideal to use for wet sanding and when used with a very fine abrasive it can give an exceptionally smooth surface which has its own gentle glow. Apply with a clean cloth or brush direct onto bare wood, up to three coats are recommended. If the oil sits on the surface and won’t soak in it means the timber has absorbed as much as it can and no further coats are needed. Any surplus can be removed with a clean cloth if required. Depending on the way the item is used it might be necessary to top-up the finish, especially if it is washed regularly. -
Velcro backed 6" (150mm) wide rolls x 1/2 metre of each of the following grits: 120G, 180G, 240G, 320G, 400G & 600G