-
Organoils Hi-Speed Finishing Oils specifically formulated for on-lathe, under-turning-speed finishing. It is a heavy oil which can well deal with the load (fill) requirements of softwoods - you may choose to cut it (with vegetable turpentine) for denser hardwoods. One of its unique ingredients is the rare, Mustard Seed Oil (a well kept Aussie secret until now!) which gives the formulation good slip for the wet-sanding procedure and a silken touch to the finished result. -
A penetrative, nourishing, quality finishing oil which reflects the original, heavy-oil formulations that traditional Danish Oils were renowned for. As a clear finish will richly enhance the existing woodcolour/s. For best results, requires quality dry-sand surface preparation; using 600 /1200 / 1500 grit papers (the finer the better) Upon curing/drying (min. 14 days) makes for ideally prepared surface for further (optional) Waxing/Polishing. -
A refined Beeswax and Citrus Oil polish with pleasant aromatics and emulsified into a ready-to-use paste. For the palest, brightest cabinetry finish offered in our range; a double wax application and polish (min. 24 hours apart) to raw, fine-sanded woodwork would be recommended. -
Boiled linseed oil is used for finishing most bare timber and suitable for replacing the natural sheen that wood can lose after long periods drying in the sun. Boiled linseed oil contains special additives which speed the drying process. Will also waterproof ground sheets and tarpaulins. -
A blend of natural plant oils to nourish and protect chopping boards and worktops. It penetrates the wood with no surface film to chip. It has a clear finish to enhance the natural beauty of wood. The Oil contains anti-microbial additives with a slow release formula which provide protection against a wide range of bacteria including E-coli and MRSA. Rustins Chopping Board Oil conforms to The Articles in Contact with Food Regulations. -
A unique formulation developed by Rustins that is suitable for all types of wood. It differs from Teak Oil in that it contains special ingredients to give it a low lustre finish. It is an easy to use wipe on finish, which brings out the beauty of the timber and gives a natural, open grained, soft lustrous finish. Ideal for all woods and is excellent on turned woodwork. Danish Oil conforms to The Articles in Contact with Food Regulations and to the Toys (Safety) Regulations 1995, BS:EN71 Part 3. -
Removal of Plastic Coating from brushes, rollers and application equipment. Also used to thin Plastic Coating when necessary if it is to be sprayed. Also used to thin the product when an opened grained oil type finish is required. -
Safety Cloth is a thick, non-woven paper cloth. Designed to stay wet longer to assist the transfer of finishes to your chosen surface, it also tears very easily if it gets caught in revolving parts thus avoiding the danger of fingers being dragged into machinery. The texture of Safety Cloth ensures that a thin, even coat is applied and the thickness means that it retains it’s strength and the same piece can be used several times with the same finish. Safety Cloth is not a replacement for common sense and good safety practise. -
This sanding sealer is designed to raise the grain and make it brittle, it can then be sanded of with fine grit abrasive paper leaving a smooth fine surface to apply finish. -
Shellac Sanding Sealer is the traditional way of sealing timber prior to applying a polish or a wax.
Chestnuts version has a high percentage of real shellac which means it does the job extremely well, dissolved in an ethanol solution to make it easy to apply and quick drying.
Applied by cloth, brush or spray it dries in about 20 minutes, making it very popular for cabinet and architectural work as it is easy to keep a wet edge running. It is also popular with woodturners and highlights the natural grain of the timber extremely well.
Sand back lightly after application and apply Friction Polish, French Polish or any of Chestnuts waxes on top.
Conforms to EN71 Part 3 – suitable for toys and nursery furniture.
-
Shellawax cream is a woodturners friction and buffing polish. Sharing many of the characteristics of Shellawax liquid, Shellawax Cream is specially formulated for use on larger turned projects where it would normally be impossible to get a first class finish using a conventional friction polish and on stand-alone articles such as carvings. As with Shellawax, only one application is required to completely finish the work. Made using a specially formulated hard shellac as a base, this excellent product gives a hard, durable finish, with impressive resistance to marks and blemishes from water, alcohol and heat. The cream formulation retards the frictional drying characteristic of friction polishes, making it suitable for use on larger lathe-turned items such as bowls and platters. Being a cream, this product is easily controlled in application and is very economical in use. Shellawax Cream is non-toxic. -
A one-application woodturners friction polish that really does work and is ideal for use on smaller spindle work such as pens and similar objects up to around 10 cm (4") diameter. This exceptional polish is made using a specially formulated hard shellac as a base to give a harder, more durable finish, giving greater resistance to marks and blemishes from water, alcohol and heat. Normally applied directly onto bare timber (though it can be used over most oils too – but test on scrap first) this polish dries almost instantly yet goes on hardening for up to three weeks resulting in a truly durable finish which far exceeds others on the market today. Once fully cured the finish is food-safe and non-toxic. -
These Mandrels are available separately or come as part of the buffing wheel kit. Both Mandrels are made in the UK and are zinc plated for maximum protection. Due to the limitations of plating a blind hole care should be taken to ensure the tapped thread of the large mandrel stays as dry as possible. The large mandrel is designed to be held in a lathe chuck. It is 25mm in diameter at its widest part, stepped to 18mm with an undercut for smaller chucks. It can be held on either, both will still give plenty of clearance from the chuck. The small mandrel is designed to be held in a jacobs chuck or similar and is especially suited to use with the smaller 4 inch wheels and the Dome Buffs. -
This clear, slower drying solvent is primarily for thinning our Spirit Stain to give delicate wash effects without affecting the colour (as methylated spirit would). It can also be used to dilute Friction Polish or French Polish if needed (usually only when the cap has been left off and the product has thickened up). It’s also suitable for use in making french polish if you want to dissolve shellac flakes in it. -
The finest of Steel Wool, very low crumble and virtually oil free to ensure there is no contamination of your work. Use it after sanding with abrasive sheets to give an ultra smooth surface, or to apply waxes to smooth the timber whilst applying a thin coat. Steel Wool burns very quickly and easily; keep it away from sources of combustion (i.e. sparks etc). Always use a knife or scissors to cut Steel Wool -
This bleached knitted cotton cloth is ideal for applying and buffing most products; the slightly coarse texture ensures that the applied coating is spread thinly, which is always preferable. Not recommended for use on the lathe. -
Tack Cloths are coated with a special, sticky resin. The resin doesn’t transfer off the cloth but when you wipe it across a surface it picks up and dust and removes it, leaving behind a clean surface ready for finishing. This makes it ideal for use after your final sanding to make sure that all of the sawdust generated is removed and doesn’t affect your finishing. Tack Cloths are supplied in a sealed wrapper; once opened store them in an air-tight container to prevent them from drying out. Do not use Tack Cloth with the lathe running. -
Tung Oil, or Chinese Wood Oil as it’s sometimes called, is a natural oil derived from the seed of the nut of the tung tree. The jury is out as to whether it can spark a nut allergy. Tung Oil air dries to form a tough, hard film that has a fairly strong amber tint. Because it doesn’t have any solvent or driers in it it can take a while to dry, and dependant on conditions this can be up to a week although 48 hours is more common. As with most finishes a thinner coat will dry quicker. Normally applied with a brush or cloth. -
Woodturners stick wax is a mixture of beeswax and carnauba wax it is slightly softer than the Carnauba Wax Stick and therefore slightly easier to apply and there are no concerns about it marking softer woods. Applied over a sanding sealer, simply hold the stick against the revolving work and allow the heat generated to melt the wax onto the wood. Buff up straight away using Safety Cloth, using the cloth to ensure an even coating. -
WoodWax 22 contains beeswax (for shine) and carnauba wax (for hardness). Blended together in a solvent to produce a soft creamy paste. This makes it very easy to apply over any surface.
WoodWax 22 is quick drying enough to be applied onto unsealed wood but works best on one of Chestnuts sanding sealers.
If working on the lathe the wax should be applied with the lathe stopped.
Apply using a cloth (Safety Cloth or Stockinette works well with this); the wax spreads easily over the surface, after about 20 seconds it starts to drag slightly. This means it is ready to buff up; if you haven’t covered the whole piece by then don’t worry, just take a little more wax from the tin and carry on applying, the wax won’t mind waiting!
It’s best to buff WoodWax 22 as soon as you can; that way any surplus wax that might have been applied will be removed, allowing the shine to really show through.
If working on the lathe Safety Cloth should be used for the buffing process and let the lathe do the work for you. Off the lathe Safety Cloth or Stockinette can be used.
A second or even third coat of wax can be applied if required, leaving about twenty minutes between coats. After three coats the finish can become softer and will mark very easily.
-
These cotton wheels come complete with the fixings needed to attach them to the mandrels in the Buffing System. Use Wheel A with Compound 1 for a preparatory cutback Use Wheel B with Compound 2 for an ultra fine surface prior to waxing Use Wheel C with Carnauba Wax Stick, Microcrystalline Wax or Microcrystalline Wax Stick. -
Shellac Sealers are used in the French polishing trade either; as a quick drying finish to seal timber after staining; or as a basecoat for subsequent coats of French Polish. -
Wax Filler Sticks are blended wax filler used to repair cracks, splits and small to medium-sized holes without sanding or having to strip the finish. Available in a wide range of intermixable wood colours, they can be applied without a heat source, are quick drying and have no shrinkage making them ideal for use on finished furniture and other articles. -
An exciting and vibrant set of colours for staining wood, Spirit Stains are methanol based to make them quick drying and because of this they also will not raise the grain of the timber they are applied to. The pigments used to make this stains are of the highest quality and all score the top ratings of 7s and 8s in the Blue Wool Scale, the measuring system used to rate fade resistance. This means you can use them with confidence knowing that the colour you apply will still be the same many years later. Spirit Stains are fully inter-mixable so you can produce virtually any colour you can think of, giving you full opportunity to be as creative as you wish. The colours will also mix after application so you can blend from one colour to another for fantastic ‘flare’ effects. Spirit Stain White is designed primarily as a mixer to create pastel shades when mixed with other Spirit Stain colours. It can be used to stain timber but as it is a translucent stain this can have a limited effect depending on the base colour of the timber used. Should you want a more subtle colour you can dilute the stains with Spirit Thinners for a delicate wash effect. -
The ideal way to experiment with the different colours available to decide which ones you prefer, the Spirit Stain Kit contains one bottle (min. contents 25ml) of each of the nine colours. These are exactly the same stain as in the bigger bottles and will intermix if you want to vary the shades available.
The stains are very fade resistant, quick drying and non-grain raising. -
The Sandmaster is an essential part of every turner's tool kit. It comes with 5 different grits of abrasive to take even the roughest projects to a glass-like finish every time. It avoids an uneven finish often associated with hand sanding and there is no danger of catching hands on the revolving project. There is little or no surface damage/head build-up, as there is with power sanding and there is no cable to trip over. Head articulates to access even the most difficult areas. Sponge head is ideal for working in tight spaces. Sandmaster creates a fraction of the dust generated by power sanding. It can be adapted to take a polishing mop. -
Super thin penetrating formula, bonds in 1 - 5 seconds. -
Allows 7 - 10 seconds for positioning, cures in 20 seconds. -
Very high viscosity formula, super thick and super strong. Allows approximately 30 - 40 seconds for positioning. Cures in 90 seconds, ideal for gap filling. Use zip kicker to accelerate cure time. -
Accelerates Super Glue cure time. Best working accelerator for ZAP. Sets in just a few seconds. -
Interior use only, initial tack time 30 mins, setting time 24 hours approximately. Open time 5 minutes, assembly time 10-15 minutes, shelf life 12 months (kept airtight).
