-
This kit gets you started on the road to buffing – all you need to supply is the lathe, a chuck and something to buff! Inside the kit you get the mandrels for holding the Buffing Wheels in the chuck. One of each buffing wheel (A, B and C) are included in the 8 inch size, complete with all the fixings attached to fit into the Mandrels. A bar of each of the compounds is included to get you started, these will last a long time so no need to worry about getting spares yet (although all of the items in the kit are available separately when you need to get them). Next is a stick of carnauba wax for that final gloss finish. Last but not least is a full set of instructions on how to use the kit to get the best from it.
-
If you need to get away from the smell and flammability of our cellulose based lacquers this is an ideal option. This water based lacquer has virtually no smell and is totally non-flammable. Don’t be fooled though, this product is extremely hard wearing and gives a full gloss finish. Being water based it is slightly slower drying, taking about twenty minutes to be touch dry. If you want to apply a second coat it should be left two hours before doing so, although a wax can be applied if required after about thirty minutes. This product can be sprayed if suitable equipment is available, or can be applied by cloth or brush. We recommend foam brushes for application as this keeps the foaming action of acrylics to a minimum.
-
These new jaws are ideal for heavy bowls and vases. The wide front face provides a good register for the base of the bowl or vase and the deep toothed body provides strong grip on the spigot. The internal gripper can also be used on smaller rough green timber. Also featuring an external dovetail in expansion, they can be used for large platters. A truly versatile and solid jaw set. Expansion: 81 - 102 mm Contraction Spigot: 46 - 65 mm Contraction Square: 33 - 54 mm
-
1" x 20' abrasive in a convenient dispenser. Perfect for spindle, pen, or any turning where small strips are needed. This convenient dispenser is loaded with four or 1" x 20' rolls of cloth backed aluminum oxide abrasive. Each dispenser pack contains one roll of 150, 240, 320 & 400 grit abrasive. Just pull out and tear off the length of abrasive strip you need.
-
Out of stockHeartwood is a vivid red when freshly cut, toning down to a medium to dark purple-brown on exposure, often with fine black lines. Sapwood is wide and greyish-white. Straight to interlocked grain with course texture. Finishes very well, tends to be dusty.
-
Ever wished you had a finish that was as easy to use as shellac but with the durability of polyurethane? Well wish no more, because here it is.
This unique Hardened Shellac creates a film with a high resistance to heat, water and alcohol, yet it is used in exactly the same was as any normal shellac. It can be applied with a rubber as French polish, brushed, sprayed and dipped.
HOW IS THIS POSSIBLE? After shellac has been dissolved in ethanol* it is possible to introduce additives that cause the shellac to cross link after it has dried. This cross linking takes about 20 days to completely cure, less in hot weather.
USES: Ideal for table tops and other horizontal surfaces such as dresser and desk tops, etc. Also brilliant for use on guitars, lutes, harps and many other musical instruments where a traditional finish is required and good resonance qualities are essential.
NEW IMPROVED FORMULA In February 2009 U-beaut began adding a plasticiser to Hard Shellac. This gives elasticity to the cured finish, to combat crazing on the thin walls of musical instruments, whilst still having the same high resistance to marking from water, alcohol and heat it has always had.
-
Liberon Finishing Oil is a blend of high quality oils for use on all interior wood and turned woodwork. Used to nourish and enhance the colour of the wood, it is suitable for use on kitchen tables and bathroom furniture, and can also be applied to cork, stone and terracotta. Water, heat, alcohol and food acid resistant, it gives a matt, satin or gloss finish depending upon the number of coats applied. Ideal for surfaces requiring a hard wearing and water-resistant finishes.
-
A good quality tailstock live centre is an essential accessory when turning between centres. Unlike traditional stationery centres, a live centre rotates with the wood, eliminating burning and increasing hold. All Record Power live centres feature high quality bearings to give long life and resist pressure during use. Sealed for life bearings ensure reliable, long lasting operation.
-
NyWeb pads are a non-woven nylon webbing with an abrasive – either silicon carbide or aluminium oxide – embedded into them to give an exactly defined cut.
- The Green pads are 400 grit
- The Red pads are 600 grit
- The Orange pads are 1000 grit
- The White pads do not contain an abrasive and are thus technically non-abrasive, but the very texture of the pads gives them an incredibly fine – but immeasurable – cut.
-
Out of stockPurpleheart has a creamy white/gray sapwood but like its name suggests, the heartwood is a bright, striking purple when freshly cut, darkening into a deeper purple with age. It has a medium to fine texture with a lustre that ranges from medium to high; its grain is usually straight but can be wavy or irregular. Purpleheart has high bending and crushing strength and stiffness with medium resistance to shock loads.
-
Crown Tools Ultra high performance 'Razor Edge' lathe turning tools combine the use of cobalt infused M42 HSS with Crown's sophisticated cryogenic treatment process to give a superior cutting edge. With beautifully crafted and distinctive 'Copper Black' handles to their 'Super Sharp Blades' these chisels are worthy of a woodturners tool collection.
-
Out of stockThe Elipse range of respirators are made in Great Britain. The mask body is made from TPE (Thermo Plastic Elastomer) a flexible material which is designed to fit the contours of the face to provide a tight seal. The filter material is known as HESPA (High Efficiency Synthetic Particulate Airfilter). Together they provide absolute protection for woodworkers. The Elipse P3 has the highest classification for a particulate filter. Surpassing the European standard EN143 by achieved 99.98% filtration at 0.3 micron. It is therefore ideal for woodturners and woodworkers, giving complete protection, even when sanding. The twin filter arrangement consists of a light weight half face mask that is comfortable to wear for long periods of time. The low profile filters provide an unobstructed field of vision. Two adjustable elastic straps securely fasten the mask to the wearer. The two strap system allows the wearer to quickly put the mask on and off the face, whilst still wearing it around the neck. Can be worn with glasses ,without causing any steaming, and other PPE safety products including visors and helmets. It is perfect for everyday use by hobby and professional users. Other applications include metalworking, welding and stonemasonry. The Elipse P3 provides protection against dust particles, metal fumes (smoke), asbestos, oil and water mists, vapours, bacteria and viruses. Replacement filters are easily fitted.
-
The ideal beginners set. These small carving tools, made from high quality hardened and tempered Carbon steel, are fitted with stained Beech handles. The ready honed blades feature 5/16" 8mm Square Chisel, 5/16" 8mm Bent Square Chisel, 5/16" 8mm Skew Chisel, 3/16" 5mm Straight Gouge, 5/16" 8mm Bent Gouge and 3/16" 5mm Bent 'V' tool.
-
If you’re looking for a clear finish that is tough, hardwearing and gives a bright gloss yet is still very easy to apply, even on larger areas, you’re in the right place. Hard Wax Oil is a particular blend of tough oils combined with special waxes which dries to an exceptionally resilient finish. Ideal for anything that is going to be subjected to water splashes or a lot of handling this oil may not be indestructible but it will stand up to a lot of abuse. It retains the ease of application typical of an oil and it stays wet long enough to get a smooth, even finish – even on large areas – but is touch dry and tack free in about 20 minutes, and better yet is ready for a second coat after about four hours (in normal conditions). Hard Wax Oil will build to a bright gloss finish after 2-3 coats. Rub down lightly between coats with a fine abrasive. Once hard dry (allow at least 24 hours) it can be brought to an even brighter shine using either the buffing wheel system or burnishing cream. For a not-quite-so-bright finish use a mild abrasive to reduce the gloss. For best results lubricate the abrasive with microcrystalline wax to retain the toughness of the oil.
-
This water based sanding sealer gets the job done without the smell associated with solvent based sealers and also with no flammability issues – ideal for asthma suffers and anyone with an aversion to solvent based finishes. Applied by cloth, brush or spray (Chestnuts' foam brushes are especially good with this) the sealer dries in about 5 minutes and can be overcoated with most compatible finishes after about 20 minutes although two hours should be left if using Acrylic Lacquer. Acrylic Sanding Sealer sands easily with a fine abrasive and is supplied ready for use.
-
It’s important to use a sanding sealer on most items; it gives a good foundation to your piece and can help the next coat to adhere properly to the timber. Chestnut Acrylic Sanding Sealer does this perfectly and is designed to be used with Acrylic Gloss Lacquer, Acrylic Satin Lacquer, Ebonising Lacquer, any of their polishes and any of their waxes. Supplied in an easy to use aerosol the dried coating complies with the EN71 Part 3 regulations governing toys and nursery furniture. Once dried lightly sand back prior to applying your top coat.
-
Planet Full Face Visor is ideally suited for woodturners and DIYers. It protects your eyes and face from woodshavings, dust, and low energy objects. Simply tighten the adjuster on the headband to get the best fit. Spare visors are also available (FV424V). The optical class Lens visor is made from clear acetate. It measure 320 x 190 mm with a nominal thickness of 1.15 mm. The visor is anti-fog (N). Recommended for protection from impact by low-energy, high-velocity particles. Full Face Yellow Visor Complete: FV424/SS/Y Visor Only: FV424V Yellow Browguard Only: FV424YV
-
Out of stock
Shellawax Glow is darker than regular Shellawax (a deep honey to tan colour). It is made from a special blend of shellacs and is designed to give more depth and richness to highly figured timbers like fiddleback, birdseye, flame and quilted woods. It will also give more richness and a sense of depth to many other timbers.
Shellawax Glow is identical in use and all other respects to regular Shellawax. It is applied in the same way and has all the same properties. It can also be mixed with Shellawax Cream as an extender and thinner and can be used over EEE-Ultra Shine.
This polish may darken white woods ever so slightly, so it is a good idea to try it on a scrap piece first to make sure it doesn't darken more than you want.
USING SHELLAWAX CREAM AS A SHELLAWAX GLOW EXTENDER Shellawax Glow can be mixed with Shellawax Cream as an extender. This allows for better use of these products on large turned work and for hand rubbed work. For bowls over (6”) 150mm diam, mix the Cream and Shellawax Glow at the rate of approx 50/50 this will give you a runny cream that will stay on the surface longer and allow you more time to work it into the timber.
Use different mixing rates for various jobs 20% Cream to 80% Shellawax Glow for large platters etc up to 900mm (3’) diam and larger.
SHELLAWAX GLOW AS A THINNER Use Shellawax as a thinner for Shellawax Cream, which often thickens with use. This will also extend the life of the Cream. The slight colour difference will not effect the colour of Cream when used.
-
The SC1 and SC2 are the first mini-chucks on the market to offer woodturners a premium-quality solution for those who regularly turn small, intricate items - bringing the world-renowned quality of the SC3 and SC4 to the mini-chuck market. The SC1 works in conjunction with a separately available insert, which means it can be used across a wide variety of lathes with different thread sizes, with a simple change of insert. It also makes a perfect partner to the SC4 chuck, as the inserts are a universal fit between both chucks. It also has a very compact 53.5 mm (2”) diameter body - giving easier access around the workpiece making it ideal for the turning of very small items. Insert must be bought separately.
-
Out of stockDeep orange-brown timber with broad medullary rays creating a flame pattern on quarter cut faces or numerous spots on flat sawn surfaces. Hard and heavy with a slightly coarse texture.
-
Related Products: These cutters are designed for use with the following tools: Medium tear-drop scraper (RS200C) to suit Multi-tip Hollowing System (RS200KT, RS200) Large tear-drop scraper(RS213C) to suit RS2000 Deep Hollowing System The Robert Sorby medium tear drop cutter, like its big brother (Large Teardrop RS213C) provides a multi-facetted, highly efficient cutting edge. The shape of the cutter effectively converts the tool into a round, half-round or square scraper suitable for use on the inside or outside of bowls, platters and hollow forms. Use the straight edge on outside curves and the rounded shapes for internal curved shapes. A great all rounder that supports traditional scraping and shear scraping techniques. Sharpening: Use a diamond file or honing stone flat across the top face. To gain best results and increase the longevity of the cutter this simple procedure should be done little and often. Use the 472 cutter holder to reshape the profile on the Robert Sorby ProEdge or on a grinding wheel.
-
Out of stockChestnut Spray Diffusers are ideal for applying Spirit Stain; one end goes in the stain and you blow through the other end for your own mini-spray gun. Great for special decorative effects.
-
This clear, slower drying solvent is primarily for thinning our Spirit Stain to give delicate wash effects without affecting the colour (as methylated spirit would). It can also be used to dilute Friction Polish or French Polish if needed (usually only when the cap has been left off and the product has thickened up). It’s also suitable for use in making french polish if you want to dissolve shellac flakes in it.
-
Made in the USA, these are the original and best quality Foam Brush. Manufactured using a special foam with a stiffener inside to make sure they keep their shape in use, and supplied with a solid wooden handle attached. Great for eliminating brush marks (no bristles = no brush marks) and there’s no danger of any stray bristles coming loose and spoiling your work. Priced to be semi-disposable they will normally wash out several times for re-use. Fantastic for applying acrylic finishes which have a tendency to froth up when applied by brush – the Foam Brush virtually eliminates this completely. Can also be used for painting, particularly gloss paints, seasoned users have been known to have a brush in each hand!