-
The ideal way to experiment with the different colours available to decide which ones you prefer, the Spirit Stain Kit contains one bottle (min. contents 25ml) of each of the twelve wood colours. These are exactly the same stain as in the bigger bottles and will intermix if you want to vary the shades available. The stains are very fade resistant, quick drying and non-grain raising. -
An exciting and vibrant set of colours for staining wood, Spirit Stains are methanol based to make them quick drying and because of this they also will not raise the grain of the timber they are applied to. The pigments used to make this stains are of the highest quality and all score the top ratings of 7s and 8s in the Blue Wool Scale, the measuring system used to rate fade resistance. This means you can use them with confidence knowing that the colour you apply will still be the same many years later. Spirit Stains are fully inter-mixable so you can produce virtually any colour you can think of, giving you full opportunity to be as creative as you wish. The colours will also mix after application so you can blend from one colour to another for fantastic ‘flare’ effects. Spirit Stain White is designed primarily as a mixer to create pastel shades when mixed with other Spirit Stain colours. It can be used to stain timber but as it is a translucent stain this can have a limited effect depending on the base colour of the timber used. Should you want a more subtle colour you can dilute the stains with Spirit Thinners for a delicate wash effect. -
These Dispensing Nozzles are, in fact, almost indispensable! They fit onto any of Chestnuts' plastic bottles in the 250ml, 500ml and 1 ltr sizes, simply replacing the existing cap. Cut the tip off to the size you want and use the handy cover to reseal them when not in use. A useful by product of using these is that if you knock a bottle over the amount you lose through the small nozzle will be much less than without it. Just don’t forget to take the nozzle off the bottle before you throw it away so that you can re-use it! These nozzles are not child resistant, the correct closure should be replaced when the product is not in use. -
This exciting range of water-based acrylic paints comes in 8 metallic colours. Designed to add an even shimmer to your work they will really make it glow. Mix and match them, use them to highlight certain areas or cover everything in them, the choice is yours. Best used over sanding sealers, apply a spray lacquer over them once dry to seal them in. Can be applied by cloth, brush, spray gun, air brush or any suitable medium you choose! -
These extended jaws act like a pin chuck, expanding into a pre-bored hole. A useful technique for free form edge bowls as you don't have to bore an exact size as with other pin jaws. The longer jaws allow for a very powerful spigot grip for smaller work. Also features a small dovetail. Expansion 26 - 46mm Contraction square: 28 - 7mm Contraction spigot 31 - 10mm -
Iridescent Paints give a change in hue, a slight colour shift when viewed from different angles and are especially effective on irregularly shaped items.Available in nine different amazingly bright and vibrant colours –- Green
- Azure
- Purple
- Red
- Turquoise
- Cerise
- Pink
- Yellow
- Vivid Blue
The paints are water based acrylics and can be applied by brush, cloth, spray gun/airbrush or any manner of ways to give interesting decorative effects. -
Iridescent Paints give a change in hue, a slight colour shift when viewed from different angles and are especially effective on irregularly shaped items.Available in nine different amazingly bright and vibrant colours –- Green
- Azure
- Purple
- Red
- Turquoise
- Cerise
- Pink
- Yellow
- Vivid Blue
The paints are water based acrylics and can be applied by brush, cloth, spray gun/airbrush or any manner of ways to give interesting decorative effects. -
This acrylic Reducer is the perfect thinner/flow medium for our Iridescent Paints and Metallic Paints, essential when using an air brush. Use sparingly, only a little should be required. This will also ensure that it does not affect the opacity and brightness of the colours. -
Keep your air brush in tip-top condition by using our Air Brush Cleaner after every use. -
Gilt Creams are a creamy, waxy paste with metallic flakes and pigments in them, giving a rich, lustrous finish to whatever they are applied to. The can be used for a ‘limed’ effect over a lacquer to give a high contrast effect, or uniformly over a piece and polished to a bright shine once dried. Available in- Gold
- Silver
- Copper
-
The Buffing Tree comprises of three 6 inch wheels, in the A, B and C cloth grades, firmly held on a central spindle. It’s ideal for buffing small items and, after loading the wheels with the compounds and wax, allows you to move from one wheel to the next in quick succession, dramatically reducing the time otherwise taken up by changing wheels. Ideal for polishing small items such as fruit, pens, boxes etc in batches. Requires one of our mandrels to fix to the chuck and a live centre for support at the tailstock. PLEASE NOTE: The Buffing Tree does not come as kit containing the mandrels and compounds etc; this is deliberate as if you already use the Buffing System you will have these and won’t want to buy them again. If you do not have these items they are available to purchase separately or as a pack in the Buffing Accessory Pack. -
These beautiful micaceous-based colours are for artists and crafters who wish to add a touch of glamour or glitter to a piece, such as the translucent glow of an angel's wings, a butterfly, a fish or the brilliant iridescent shimmer on a mallard drake's neck. Simply mix the iridescent colours directly into your paints or apply after decorating to highlight specific areas. The choice is yours. For best use when using the Iridescent paints in an Airbrush, looks well on an ebonised background. -
Although French polish is the general term for all types of Shellac Polish, it is also a product in its own right. Mylands range contains many blends of Shellac Polish which have been developed over the years to fulfil various different requirements – some of which are slightly modified products for a specific purpose. They come in various depths of colour, which give the French Polisher latitude to choose the most appropriate product for the timber being polished. Shellac products have a variety of uses from finishing antiques and reproduction furniture to acting as a barrier between two normally incompatible finishes. They are particularly useful when refurbishing furniture as they will seal in any wax product which may have been applied to the furniture in the past. -
Shellac Sealers are used in the French polishing trade either; as a quick drying finish to seal timber after staining; or as a basecoat for subsequent coats of French Polish. -
Used for diluting French polish, Light Fast and Earth Stains, or cleaning surfaces and tools.
-
A low sheen finishing oil based on Tung Nut Oil, Beeswax, Citrus solvents and anti-fungal oils that penetrates the timber substrate to nourish, preserve and seal; as well as providing protection against weather degradation and rot. A natural alternative to petroleum hydrocarbons and water based oils -
A penetrative, nourishing, quality finishing oil which reflects the original, heavy-oil formulations that traditional Danish Oils were renowned for. As a clear finish will richly enhance the existing woodcolour/s. For best results, requires quality dry-sand surface preparation; using 600 /1200 / 1500 grit papers (the finer the better) Upon curing/drying (min. 14 days) makes for ideally prepared surface for further (optional) Waxing/Polishing. -
Organoils Hi-Speed Finishing Oils specifically formulated for on-lathe, under-turning-speed finishing. It is a heavy oil which can well deal with the load (fill) requirements of softwoods - you may choose to cut it (with vegetable turpentine) for denser hardwoods. One of its unique ingredients is the rare, Mustard Seed Oil (a well kept Aussie secret until now!) which gives the formulation good slip for the wet-sanding procedure and a silken touch to the finished result. -
This is an oil type finish similar to Danish oil but nothing like it. This product is designed to be hand rubbed on to raw timber, giving a finish with a hard, bright, high gloss. It will bring out amazing depth and brilliance to most timbers making the grain pop and become opalescent, vibrant, shimmering and alive. Especially when used on a fine grained, highly figure timber. And if that's not enough it does it all in a matter of minutes.
Aussie Oil is ideal for use on most small items like pendants, brooches, earrings, small turned items that cannot be fully finished on the lathe. Pens, magnifying glass handles, compacts, key rings, letter openers, in fact almost anything made of wood you can comfortably hold in your hand to polish.
As an extra added bonus, it also works brilliantly as a friction polish on the lathe.
-
Shellawax cream is a woodturners friction and buffing polish. Sharing many of the characteristics of Shellawax liquid, Shellawax Cream is specially formulated for use on larger turned projects where it would normally be impossible to get a first class finish using a conventional friction polish and on stand-alone articles such as carvings. As with Shellawax, only one application is required to completely finish the work. Made using a specially formulated hard shellac as a base, this excellent product gives a hard, durable finish, with impressive resistance to marks and blemishes from water, alcohol and heat. The cream formulation retards the frictional drying characteristic of friction polishes, making it suitable for use on larger lathe-turned items such as bowls and platters. Being a cream, this product is easily controlled in application and is very economical in use. Shellawax Cream is non-toxic. -
This amazing product is a cut and polish paste containing Tripoli powder, an ultra-fine abrasive. The polish is designed to be used in conjunction with Shellawax Cream and liquid formulations or as a finish in its own right on plastics (such as acrylic, resin-impregnated burr, crushed velvet, artificial ivory and similar products used for pen bodies). It can also be used after French polishing and restorers will find it useful to cut and revive previously polished surfaces. Although designed to be used directly on raw timber, bear in mind that EEE is not a finish in itself and the polished surface will need protecting by the use of some other product (such as Shellawax). EEE-Ultra Shine can be used over many other finishes such as oils and most types of varnish, enhancing the surface and giving it a smoothness and lustre with an ease that you would never have thought possible. -
Out of stock
Ever wished you had a finish that was as easy to use as shellac but with the durability of polyurethane? Well wish no more, because here it is.
This unique Hardened Shellac creates a film with a high resistance to heat, water and alcohol, yet it is used in exactly the same was as any normal shellac. It can be applied with a rubber as French polish, brushed, sprayed and dipped.
HOW IS THIS POSSIBLE? After shellac has been dissolved in ethanol* it is possible to introduce additives that cause the shellac to cross link after it has dried. This cross linking takes about 20 days to completely cure, less in hot weather.
USES: Ideal for table tops and other horizontal surfaces such as dresser and desk tops, etc. Also brilliant for use on guitars, lutes, harps and many other musical instruments where a traditional finish is required and good resonance qualities are essential.
NEW IMPROVED FORMULA In February 2009 U-beaut began adding a plasticiser to Hard Shellac. This gives elasticity to the cured finish, to combat crazing on the thin walls of musical instruments, whilst still having the same high resistance to marking from water, alcohol and heat it has always had.
-
Perforated design which allows the dust to escape without clogging. mixed pack of 15, 3 of each of the following 5 grits, 120G, 180G, 240G, 320G 400G, 70mm x 125mm. -
Perforated design which allows the dust to escape without clogging.
-
Removal of Plastic Coating from brushes, rollers and application equipment. Also used to thin Plastic Coating when necessary if it is to be sprayed. Also used to thin the product when an opened grained oil type finish is required. -
A unique formulation developed by Rustins that is suitable for all types of wood. It differs from Teak Oil in that it contains special ingredients to give it a low lustre finish. It is an easy to use wipe on finish, which brings out the beauty of the timber and gives a natural, open grained, soft lustrous finish. Ideal for all woods and is excellent on turned woodwork. Danish Oil conforms to The Articles in Contact with Food Regulations and to the Toys (Safety) Regulations 1995, BS:EN71 Part 3. -
3" arbors 75mm x 6mm spindle pad with 20mm foam
-
3" velcro (hook and loop ) backed abrasive sanding discs. Designed to be used in a power drill. Available in 80G, 120G, 180G, 240G, 320G & 400G. -
A blend of natural plant oils to nourish and protect chopping boards and worktops. It penetrates the wood with no surface film to chip. It has a clear finish to enhance the natural beauty of wood. The Oil contains anti-microbial additives with a slow release formula which provide protection against a wide range of bacteria including E-coli and MRSA. Rustins Chopping Board Oil conforms to The Articles in Contact with Food Regulations. -
Boiled linseed oil is used for finishing most bare timber and suitable for replacing the natural sheen that wood can lose after long periods drying in the sun. Boiled linseed oil contains special additives which speed the drying process. Will also waterproof ground sheets and tarpaulins. -
Worktop Oil is a unique water-borne blend of natural plant oils and other special ingredients which nourishes and protects all types of timber. It is a quick-drying wooden work surface treatment, leaving a durable and water-resistant seal which is not vulnerable to scratching or chipping. Plant oils used in its formulation originate from sustainable sources. One litre will cover around 13 square metres per coat depending on the absorbency of the wood.- Water based & quick drying
- For all solid wood worktops
- Low odour
- Food safe
- Natural finish
-
metal hands plus matching black second hand
