-
Interior and exterior use, strong initial tack with fast setting. Excellent sandability, unaffected by finishes. FDA approved for indirect food contact and easy to clean away with water. Open time 5 minutes, assembly time 10-15 minutes, shelf life 12 months (kept airtight). -
Interior use only, initial tack time 30 mins, setting time 24 hours approximately. Open time 5 minutes, assembly time 10-15 minutes, shelf life 12 months (kept airtight). -
Allows 7 - 10 seconds for positioning, cures in 20 seconds. -
Very high viscosity formula, super thick and super strong. Allows approximately 30 - 40 seconds for positioning. Cures in 90 seconds, ideal for gap filling. Use zip kicker to accelerate cure time. -
Accelerates Super Glue cure time. Best working accelerator for ZAP. Sets in just a few seconds. -
Out of stock
Aids in removing cured superglues from skin and work surfaces. Debonding agent for all super glues. Always test first. 1-oz bottle. -
Super thin penetrating formula, bonds in 1 - 5 seconds. -
Milliput Epoxy Putty, the two sticks have a long shelf life but once mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. Speed of hardening is dependant on temperature and at normal temperatures (20-25ºC) Milliput becomes rock hard in three to four hours. By the application of heat the setting time can be reduced to a few minutes. After setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time at the same temperature. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted. Milliput can be sandpapered and painted immediately it has set. (it is advisable to wear eye protection during this process). Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive and should not be used where a paste, mucilage or thin glue is indicated. Milliput will set under water and is heat resistant up to 130°C. Shelf Life: Recommended that Milliput is stored in cool, dry conditions. Please reseal bags after use. Stored correctly this product should remain workable for about 2 years. Available in six colours: Standard (Yellow/Grey), Terracotta, Silver Grey, Black, Superfine White and Turquoise Blue. -
Out of stock
While this resin has been manufactured to resist scratching and resistance to marking from heat sources we must stress this resin will still mark if sharp items are moved across the surface or hot items are placed on the surface.
As with all casting products, we stress that customers should purchase a small amount to perform initial tests to ensure suitability for their project and requirements.
Pigmentation Epoxy pigments are the recommended system to colour this resin however the polyester range of pigments will also work. Please read the Technical and Safety Data sheets prior to use. We recommend small scale testing to ensure compatibility before using at full scale. Cold Weather Notice Cooler temperatures in the UK and Ireland around mid-autumn to mid spring are not ideal conditions for water clear epoxy systems, this can increase the chances of crystallisation in the resin (this can occur at room temperature depending on circumstances, it is however much less common). Appearance can differ depending on the degree of crystallisation, from small lumps sitting on the surface to a hazy/milky white appearance, extreme cases the contents may completely solidify. Crystallisation occurs due to a phase change from liquid or solid similar to that of water turning to ice, fortunately it is easily reversed by warming the epoxy component to 60°c. Ensure any crystals are completely removed as remaining crystals can act as a seed causing the crystals to form again quite quickly. Lab results show the heating cycle to remove crystals can be repeated on multiple occasions before beginning to suffer from any losses in resin properties. We recommend keeping the resin system at a good room temperature at all times where possible, ensure to clean the lids and bottle necks of containers with isopropyl alcohol / acetone allowing the solvent to evaporate before replacing the lid.Product Data Units Mix Mix Ratio Weight 100 : 50 Hardness ShoreD 80 - 85 Viscosity (25°C) mPa.s 600 - 900 Density (25°C) g/cm3 1.09 – 1.13 Pot life (200g, 25°C) Mins 25 - 30 Cure Time (200g, 25°C) Hours 24 Full Cure (25°C) Days 7 Recommended Casting Thickness mm 1 - 5 -
Llewellyn Ryland Polyester Pigment are coloured liquid/paste mediums based on pigments dispersed within a solvent-free reactive unsaturated polyester resin. They are available in a wide range of colours varying in strength and consistency depending upon the particular colouring application. They have been developed to blend easily into resin systems. The range of colours is based upon pigments carefully selected for colour fastness, opacity, heat stability and having minimum effect upon the curing characteristics of the final system. The resin used with the Polyester Colour Paste is a specially developed solvent-free reactive polyester resin which chemically cross links with the moulding resin so that the colour is "locked in" once the system has cured. They can be used to colour most polyester resin based systems used within the composites or related industry. These Polyester Colour Pastes have excellent stability. -
Made from Nickel Chromium wire and with normal use will last many years. -
- Make points to your shape and design using wire cutters and pliers. One reel can make in excess of 150 points. Hammered flat, they can be used as a blade for burning feathers, grass or fur, or file the wire to a needle point for minute detail.
-
- Designed for use with the Peter Child Pyrography machine: two pen flexibility at the flick of a switch.
-
Features:- Fine control of heat and precise handling of the burning head, variable heat, up to 1100º C.
- The pen (for handpiece) has a cool running and lightweight handle which remains comfortable even after many hours of use.
- Writes quickly and as fluently as a fountain pen.
- Cost effective replacement points.
- The ability to shape your own points from specialist wire with the supplied fine wire, perfect for fine detailed burning. Thicker wire is available, ideal for enhancing bird or stick carving.
-
Sale!
The Record 8" Buffing Machine is the ideal solution for buffing and polishing woods as well as some metals and can be used in conjunction with pastes and compounds on a wide range of surfaces. It features a heavy-duty cast iron base which can be bolted to a bench and rubber feet to reduce vibration, making for smooth and stable running. The machine is supplied with two high-quality 8” (200 mm) diameter fine buffing wheels to ensure an excellent finish is achieved.
