-
Long series sawtooth Forstner cutter Long series forstner bit (inch), sawtooth pattern, particularly suited for cutting down the grain. Long series - all sizes are a minimum of 150mm long, will produce over-lapping holes, resharpenable. -
Long series sawtooth Forstner cutter Long series forstner bit (mm), sawtooth pattern, particularly suited for cutting down the grain. Long series - all sizes are a minimum of 150mm long, will produce over-lapping holes, resharpenable.
-
The parabolic flute design clears the chips quickly. Precise when boring into end grain. Packed in reusable tubes with euro slot. -
Forstner Extension bar shanks are available in two sizes, to suit Planet's long series saw tooth forstners: 3/8" collar /200mm long Forstner Extension Bar. For sizes 3/8" to 2" 1/2" collar /280mm long Forstner Extension Bar. For sizes 2 1/4" to 4" -
Designed with an internal dovetail to fit securely onto the standard 2" (50mm) jaws. These rings work in the same way as normal faceplates but with the convenience of the easy chuck fitting. Available with an outer diameter of 3⅛" (80mm) and 4¾" (120mm). -
These extended jaws act like a pin chuck, expanding into a pre-bored hole. A useful technique for free form edge bowls as you don't have to bore an exact size as with other pin jaws. The longer jaws allow for a very powerful spigot grip for smaller work. Also features a small dovetail. Expansion 26 - 46mm Contraction square: 28 - 7mm Contraction spigot 31 - 10mm -
Featuring a specialised dovetail profile, these jaws are ideal for turning large bowls, green timber and hollow vessels. They combine the profile of our previously popular 100 mm dovetail jaws with a deep body and internal teeth to improve versatility. The outer dovetail jaws are ideal for large bowls or platters, particularly when gripping onto a spigot and the deep internal toothed body is ideal for large spigots of large hollow vessels. Expansion: 94 - 114 mm Contraction Spigot: 76 - 95 mm Contraction Square: 54 - 74 mm -
Featuring a specialised dovetail profile, these jaws are ideal for turning up to 30” bowls. They also feature a reverse dovetail for a contracting grip on large spigots. Expansion: 125 - 145 mm Contraction Spigot: 104 - 123 mm Contraction Square: 74 - 94 mm . -
This faceplate ring is ideal for holding medium sized bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 50 mm jaw set which comes complete with all Record Power chuck packages. Must be used with: 62313 50 mm Standard Jaws (Supplied with SC3 and SC4 chucks) Diameter: 87 mm -
These jaws are a smaller version of the standard 50 mm jaws, featuring the same dovetail profile in expansion and the superb grip of the hawk beak design on contraction. Designed specifically for smaller spigots and recesses, this set is incredibly versatile and makes a great addition to any turner’s tool collection. Expansion: 38 - 58 mm Contraction Spigot: 28 - 47 mm Contraction Square: 16 - 37 mm -
This large faceplate ring is ideal for holding large bowl blanks and due to its strong hold is also suitable for more out of balance timber. It is held to the chuck using the standard 50 mm jaw set which comes complete with all Record Power chuck packages. Must be used with: 62313 50 mm Standard Jaws (Supplied with SC3 and SC4 chucks) Diameter: 100 mm -
These new jaws are ideal for heavy bowls and vases. The wide front face provides a good register for the base of the bowl or vase and the deep toothed body provides strong grip on the spigot. The internal gripper can also be used on smaller rough green timber. Also featuring an external dovetail in expansion, they can be used for large platters. A truly versatile and solid jaw set. Expansion: 81 - 102 mm Contraction Spigot: 46 - 65 mm Contraction Square: 33 - 54 mm -
These extremely flexible jaws feature internal and external dovetails for bowl work. The deep internal grip is versatile but main benefit of these jaws is to project the work away from the chuck, allowing good tool access to the base of the timber for cleaning and shaping. Expansion: 54 - 74 mm Contraction Spigot: 38 - 58 mm Contraction Square: 27.5 - 48 mm -
To complement the new pin jaws, the mini spigot jaws have also been improved. These jaws perform many of the same tasks in expansion and the extra screw hole profiles and added teeth to the outside provide tremendous grip for when this area will not be visible in the finished work piece. This set has been given a 13 mm internal diameter, making it ideal for turning strong spigots on knobs and handles, again adding to their versatility. Expansion: 26 - 46 mm Contraction Spigot: 13 - 33 mm Contraction Square: 11 - 31 mm -
These jaws are fantastically effective for drilling pen blanks. They eliminate the need for a drill press and offer much more accurate results and the deep grip to all four sides ensures incredible holding power. Drilling on the lathe means the feed speed of the drill bit is under your complete control, meaning a superior finish can be achieved on a wide range of materials. These jaws are also useful for working on small finials and similar projects as in addition to their strong grip, the work piece is moved forward from the chuck, allowing greater access. Contraction Square: 10 - 26 mm Contraction Spigot: 11 - 20 mm Expansion: 35 - 64 mm -
Records' new pin jaws have been improved by squaring the external shoulder to allow workpieces to properly register against the back of the jaws. This is ideal for use in expansion, to grip tubes in work pieces such as pepper or salt grinders. We have also reduced the internal diameter to 9 mm, making it ideal for making finials or lace bobbins - Thereby increasing its versatility. This set is ideal for miniature turning and to grip workpieces internally without excessive damage or marking. Expansion: 28 - 45 mm Contraction Spigot: 9 - 28 mm Contraction Square: 7 - 27 mm -
Out of stock
These nylon jaws are designed specifically to be cut with standard turning tools. They can be easily shaped to create bespoke jaws to fulfil exacting requirements and offer excellent grip without marking the work piece. Diameter: 118 - 140 mm Depth: 26 mm -
Out of stock
Record have increased the capacity of their larger remounting jaws, whilst ensuring they can still clear the bed of lathes with the popular 12” swing capacity and are capable of holding 275 mm (10 3/4”) diameter bowls in contraction mode. Remounting jaws are incredibly popular due to their flexibility. They work in both contraction and expansion modes and can be fitted behind other jaw sets to create bespoke set-ups to make turning more efficient. The soft stoppers are designed to hold without causing damage, making them ideal for remounting finished or partly finished objects for further work. -
Remounting jaws are incredibly popular due to their flexibility. They work in both contraction and expansion modes and can be fitted behind other jaw sets to create bespoke setups to make turning more efficient. The soft stoppers are designed to hold without causing damage, making them ideal for remounting finished or partly finished objects for further work. Expansion: 95 - 215 mm Contraction Spigot: 59 - 170 mm Contraction Square: 53 - 154 mm -
Record SC4 Professional Geared Scroll Chuck Package with no insert is perfect for the demanding woodturner, being capable of holding large work pieces yet possessing the precision and compactness to handle more delicate work. This model features an enclosed back with full indexing plate and has pinions driven by a long ball ended hex key to make access easy, even when large work pieces are mounted. This chuck is an insert model which means it is easily future proofed against upgrades and can be used on multiple lathes, even if they have different spindle threads (additional optional inserts required).Supplied complete with the deep wood screw, 50 mm standard jaws, 2” faceplate this package offers professional performance at an exceptionally affordable price.Please order SC4 chuck insert to suit your lathe -
Specially designed to provide a strong contracting grip to unsupported spigot turning applications, e.g. vases and goblets. It can handle spigots from 30mm (13/36inch) to 50mm (2inch). Also features expanding grip mode.
-
Record SC3 Chuck Package is lighter and more compact than the SC4, making it ideal for use on any lathe, particularly small to medium sized machines and is still compatible with the full jaw range. The compact design reduces load on the lathe spindles and bearings and gives good access to smaller work pieces. The large jaw slides offer unrivalled strength and holding power that cannot be found in other chucks of this size.Supplied complete with the deep wood screw, 50 mm standard jaws and 2” faceplate this package offers unrivalled value. -
Chuck Insert to fit the Record Power SC1 Mini Chuck and SC4 Professional Geared Scroll Chuck only. -
This modular tool rest system enables the turner to build up a collection of tool rests without going to great expense. Six different rests are available: 4", 6" and 9"as well as a 9" curved internal and external and a box platform which can be used in conjunction with just one stem. Cross bars are specially hardened to avoid those troublesome nicks and to give a smooth finish. Stems are available in ½", ⅝", ¾", ⅞", 1", 25mm, 28mm and 30mm diameters to fit most popular lathes. The same stems are compatible with the Precision Boring System. -
The original Stebcentre is an invaluable accessory for every woodturner. Fitted in the lathe head-stock it is a boon for both the novice and the experienced. Its ring of sharp teeth ensure that the Stebcentre bites the wood to give more security and more drive. Because there are several points of contact there is minimal risk of splitting. The Stebcentre can be used with equal confidence on both soft and hardwoods as well as synthetic materials. In its patented design the Stebcentre also features a spring-loaded point. By slightly backing off the tail-stock the work piece still remains resting between the revolving centre and the Stebcentre. This allows the turner to inspect his work without the need to switch off the lathe. Where time is a critical factor the Stebcentre is ideal as the work-piece can be quickly removed without stopping the lathe. Overall length: 4". Patent No. 2286138 -
Largely inspired by Norwegian turner Petter Herud a series of Revolving (or Live) Stebcentres has been introduced. Not only do these offer the same degree of security as the conventional Stebcentre, but they have allowed the turner to experiment with basic off-centre turning. Visit www.robert-sorby.co.uk to download instructions on how to produce multi-sided dishes and bowls. -
Cross bars are specially hardened to avoid those troublesome nicks and to give a smooth finish. -
This heavy duty belt and disc sander has plenty of power to handle demanding sanding whilst also being capable of fine and delicate work. The solid cast iron table provides ample support and the 1 hp motor provides plenty of power to avoid stalling under pressure. Shown with optional leg stand.
-
for use with BDS150 for 6" x 4" Belt & Disc Sander -
The BBS1 is a hugely versatile machine, particularly useful for tight curves as well as more sweeping contours, this bobbin sander allows beautiful, crisp results to be achieved with ease. The machine comes with two bobbins and corresponding table inserts and a range of additional sizes are also available. The BBS1 allows a wide array of shaping tasks to be accomplished with ease, from intricate craft projects to larger work on cabinets, chairs and much more. In addition, the powerful and quiet 1/2 hp induction motor ensures larger timbers can be handled effectively and easily. The finely ground cast iron surface also helps easy movement of the timber whilst providing extremely solid support. The build quality, features and versatility of this machine makes it an essential tool in almost any workshop. -
for use with BDS150 for 6" x 4" Belt & Disc Sander -
With a cast iron table at the heart of this compact machine it is designed to offer those with limited space or budgets a real bandsaw with sensible capacity and performance, as an alternative to lightweight hobby machines. The BS250 should not be confused with the lightweight hobby machines available in the market at a similar price. It shares the same essential build qualities as its larger cousins – strong steel frames, dynamically balanced bandwheels, cast iron tables and an induction motor. It has been designed to offer the user with space restrictions a serious machine in compact form. The machine can be bench mounted or fitted to the optional stand and wheel kit, providing great flexibility in a tight space.
-
The BS300E is a great all rounder perfectly specified for the medium sized workshop where a range of duties will be required.Featuring a solid fence, vital for accurate ripping, which has a heavy extrusion mounted on a cast iron base and fixed to a solid steel bar for maximum rigidity and support. This is based on an industrial Startrite design and much more solid than other fences at this level. The machine also features a solid double trunnion fence mount to provide rigid table support and one-handed table tilt on a smooth rack and pinion. Adding to the structural integrity of the BS300E are the cast iron bandwheels which are fitted with precision ground rubber tyres to provide a flywheel effect for smooth cutting. A solid blade tension indicator is fitted to the rear of the machine to allow for easy setup. The BS300E is also supplied with a basic wheel kit as standard. -
An ideal workhorse for the busy workshop where power and generous capacity are required but budget and space do not allow a bigger machine. This features an open legstand, often requested by our users as it provides greater stability and can be used with an optional pedal style wheelkit. A basic wheelkit is provided as standard. The bandwheels are cast iron and dynamically balanced with precision ground, crowned rubber tyres usually only found on much more expensive industrial machines – the flywheel effect of the cast iron wheels improves cutting performance and speeds. Our tables are some of the largest in their category and a one piece cast double trunnion has been designed to provide even greater support and rigidity. The rip fence is the strongest and most industrial in its category with a chromed fence and the mount machined from a single piece of cast iron. The extrusion itself is a heavy section to provide rigidity and accuracy. -
Skip tooth pattern to suit BS250 & Sabre 250. Also fits RSBS10, Clarke CBS335, Nutool HBS14 -
Skip tooth pattern to suit BS300E. Also fits Startrite 301S/301E, Poolewood 1402, Scheppach Basato 3
-
Outside caliper with fine adjustment for measuring spindle diameters when turning between centres.
-
Divider with fine adjustment for measuring between two points, scribing circles prior to turning, marking along a spindle etc. -
Inside caliper with fine adjustment suitable for measuring internal dimensions, eg turned boxes. -
Outside caliper with fine adjustment for measuring spindle diameters when turning between centres. -
The Robert Sorby ProEdge takes all the guesswork and effort out of sharpening all your woodworking, woodturning tools. The ProEdge has an abrasive belt which is a quick and efficient method of putting a keen edge on each and every tool. The cool running belt avoids any overheating. The ProEdge comes complete with aluminium oxide and zirconium belts. The ProEdge requires no complex assembly - it can be plugged in and used straight from the box.
-
The ProEdge Deluxe system includes a skew jig, a standard gouge jig, a fingernail profiler and three different belts in addition to the basic system. -
Out of stock
Featuring a spiral twist, these plain end HSS blades can cut in any direction without the need to turn the workpiece. This is particularly useful for projects that are too big for the throat depth of the scroll saw. They also allow for pieces to be cut with the bevel running in the same direction all round. 0.8 mm wide, 0.34 mm thick, 40 TPI. -
These pin end blades are ideal for use in machines that only accept pin end blades, but can also be used in machines that feature universal jaws. Their width makes them ideal for straighter cuts and for more arduous cuts, such as deep hard woods. Perfect for small joints and box making. 3 mm wide, 0.5 mm thick, 20 TPI. -
These pin end blades are ideal for use in machines that only accept pin end blades, but can also be used in machines that feature universal jaws. Their width makes them ideal for straighter cuts and for more arduous cuts, such as deep hard woods. Perfect for small joints and box making. 3 mm wide, 0.5 mm thick, 15 TPI.
-
These pin end blades are ideal for use in machines that only accept pin end blades, but can also be used in machines that feature universal jaws. Their width makes them ideal for straighter cuts and for more arduous cuts, such as deep hard woods. Perfect for small joints and box making. 3 mm wide, 0.5 mm thick, 10 TPI
-
The width of these pin end blades makes them ideal for straighter and more arduous cuts, such as deep hard woods. The tooth pattern makes them ideal for faster cutting as they provide better chip clearance than standard tooth patterns. 3 mm wide, 0.5 mm thick, 9 TPI. -
The width of these pin end blades makes them ideal for straighter and more arduous cuts, such as deep hard woods. The tooth pattern makes them ideal for faster cutting as they provide better chip clearance than standard tooth patterns. 2 mm wide, 0.25 mm thick, 18.5 TPI.
-
The skew jig is for accurate sharpening of woodturning skew chisels. -
Out of stock
The standard gouge jig allows easy sharpening of all standard ground woodturning gouges. -
The woodworking chisel jig accurately ensures a straight cutting edge on any woodworking chisel. -
The long grind jig helps you create three different fingernail profiles on bowl and spindle gouges. -
The cutter holder is a great and inexpensive sharpening accessory. Being double ended it allows the turner to hold comfortably almost every Robert Sorby tool tip without the fear of catching fingers on a sharpening belt or grinding wheel.
-
The honing wheel arbor mounts the Honing Wheel to the ProEdge sharpening system. -
The abrasive honing wheel that can be shaped to allow honing of gouge flutes, especially useful for the woodcarver. -
Applied to a buffing mop the honing paste creates a highly polished finish on any steel. -
Out of stock
The pigtail mandrel is used to mount the Buffing Mop to the ProEdge sharpening system. -
Out of stock
The buffing mop gives that extra fine edge. -
Achieving the exact bevel angle on any fingernail or long grind gouge has never been easier than with the Robert Sorby Proset. -
40 micron -
A wet stone sharpening system with a range of jigs and accessories and is also an extremely useful tool for general household tasks, such as the sharpening of knives, gardening tools and many other items. Included in this package is the WG250/K Diamond Trueing Tool, an essential accessory to ensure the outer diameter remains concentric and the sharpening surface perfectly flat. For more details and to see a video click on more info button. -
Included with the machine are a range of essential tools and jigs, not only making this package fantastic value for money but also allowing accurate sharpening straight from the box. A full range of optional jigs and accessories are available which are compatible with the 12 mm bar system of the Record Power WG250. The WG200 features smooth and responsive variable speed. The torque can also be adjusted, enabling heavier grinding without fear of the stone or honing wheel slipping under pressure.
-
The new DML320 lathe offers fantastic value for money, being compact and powerful yet with very generous capacities for a medium sized lathe, giving woodturners the chance to own a high quality variable speed machine at an unbeatable price. The solid cast iron bed, tailstock and headstock offer superb stability, even when turning items at the limits of the lathe’s considerable capacities. At the heart of this machine is the high quality electronic variable speed function, giving smooth and responsive speed change at the turn of a dial, with a highly accurate digital speed readout. The 3 pulley system ensures excellent torque across the full range of speeds and is powered by a high quality and vibration-free motor. The DML320 is also capable of reverse turning, ideal for achieving a perfect finish when sanding.
-
The DML305 cast iron lathe represents a new benchmark in high quality midi lathes and is perfect for the user with minimal space or as a second lathe for demonstrations and shows. The bed is made from finely ground cast iron for weight and rigidity and fitted with cam locking tool rests that clamp easily and solidly to the bed with one handed operation. The machine has 393 mm between centres as standard and an optional bed extension can be added to increase this capacity.
The swing over the bed is 305 mm and the motor is 1/2 hp, providing plenty of power for the capacities of these machines. The spindle has an M33 thread to ensure a wide range of Record Power accessories can be fitted.
This lathe is extremely well finished with polished metal handles, spindle locks with indexing and graduated markings on the tailstock barrels. Many of these features are normally only found on expensive professional lathes.
-
The DML250 is a compact and extremely well built machine that offers excellent performance and exceptional value for money. The finely ground cast iron bed, along with the cast iron headstock, tailstock and tool rest, greatly reduce vibration and provide ample strength for the lathe to cope with heavy duty work. The capacities of this machine and its overall size make it a perfect choice for the smaller workshop. It is also ideal as a second lathe for regular use on small work and its portability means it can be used at demonstrations and shows. -
This brand new lathe from Record Power represents the culmination of many decades of expertise in the manufacture and supply of superior woodturning lathes. Developed with the help of professional woodturners and keen hobbyists, Record believe they have produced a world-class machine for woodturners of all levels. Thanks to a number of innovative design solutions the capabilities, features and performance of the Herald far exceed anything a machine of this size has been capable of before - It brings top-end professional performance at a fraction of the size and cost of comparable heavy-duty machines.To reflect the Record Power heritage in a modern context, the look of the lathe incorporates the elegant and balanced curves of the earlier Coronet series in a more streamlined and efficient form. As well as looking great, the Herald feels great - the excellence of engineering, ergonomics and quality manufacturing can be felt throughout, making the lathe a pleasure to use whilst delivering rock solid performance. -
Out of stock
The midi sized lathe continues to be Charnwoods' best seller. It is a size which can accomplish most of the projects turners are likely to try and is the largest lathe which can comfortably be moved off the bench when not in use. We have developed ours further this year to now include an indexing system on the headstock spindle as well as more robust electronics, specifically designed for UK voltage. The bed of the lathe is one-piece precision ground cast iron giving 14" between centres when working with our new heavy duty centres, which are supplied as standard. The bowl turning capacity of 12" diameter over the bed, requires a very low speed which is achieved using a converter and a DC motor. A clear LCD display shows the current RPM. The tool rest banjo is a cam-lock design for rapid adjustments with all metal components. The tool rest itself is our ever popular round bar made from hardened steel The headstock is hollow centred to allow for easy tool removal, the tailstock is also hollow and has automatic centre removal. Supplied with drive and tail centres 2MT, knockout bar, 6" toolrest with 5/8" shank, 3" diameter faceplate, tool holder, carrying handles and cable tidy. N.B. The distance between centres will vary and be dependent on the type of centres or accessories used. Maximum distance is 450mm (18"). -
This stand and wheel kit provides great flexibility for those with a small workshop or for people who may need to move the machine on a regular basis. -
Record Power's powerful work lamp is a perfect addition to any workshop. The long flexible neck allows it to be positioned to illuminate even the most hard-to-reach areas and get rid of troublesome shadows, giving a clear view of the work in progress. To further increase the lamp’s flexibility, a sliding collar on the lamp head allows either a spotlight or floodlight beam to be created. The strong magnetic base and magnetic side clip mean the light can be secured virtually anywhere on a machine. Powered by either standard AA batteries or a USB rechargeable lithium battery, this lamp gives hours of uninterrupted use and is ideal for a wide variety of machines such as scroll saws, bandsaws, sharpening machines, lathes and many more.Includes:• Magnetic base• Magnetic side clip• AA and Lithium battery holders• Micro USB-A cable -
This robust material is designed to handle the demands of all steels. Not strictly ‘grit sizes’ these belts are built using brick and pyramid abrasive shaping. The highest 3000 ‘grit’ size will sharpen to two microns (the same sharpness as a disposable razor blade) and provide a factory finish on all steels. -
This hardwearing material is a great choice for profiling and re-profiling damaged tools. The heavier 60 grit option is an efficient choice for removing plenty of material, while the finer 120 grit will provide a satisfying finish. Great longevity and highly practical. -
Out of stock
When it is critical to drill a hole at a certain angle or the hole needs to be stopped at a specific depth, there really is no substitute for a dedicated drilling machine. By setting up the work piece and clamping it to the table all guesswork is eliminated and accurate and repeat drilling becomes simple and easy. Record Power have long had a reputation for fine drilling machines and our current range is no exception. Making extensive use of steel and cast iron and driven by a powerful induction motor, the DP58P can be expected to give reliable service for many years. The headstock in particular is made from a large casting to give rigidity and absorb vibration. The large, heavy table is fitted with rack and pinion rise and fall. The machine has 12 speeds, making it suitable for drilling metal as well as wood. This is particularly useful as most woodworkers have the occasional need to drill metal for hinges, brackets and plating etc. and it can be very frustrating to have the right machine for the job but not the right speeds. Record Power have a high reputation for quality drilling machines and we believe that when this machine is compared to others in the market at similar (or greater) prices the value for money it represents will be quickly appreciated.
-
Out of stock
A good quality, dedicated drilling machine is an indispensable tool in any workshop. The DP25B brings this versatility, along with traditional Record Power build quality and reliability, within easy reach of the home woodworker and discerning DIY enthusiast. A wide variety of bits can be accepted and the five speeds allow for a great variety of materials to be drilled, including wood, metal, plastic and many others. The cast iron table can tilt up to 45º and will accept most drill press vices, allowing secure holding for increased accuracy and safety. When extra capacity is needed the table can be moved to the side of the machine so the base can be used as a working table, which also accepts drill press vices. For further strength and performance, the headstock also features cast iron, adding weight to reduce vibration, along with a cast iron handwheel. The DP25B features an easy to use locking collar depth stop. To support it's large capacities, the machine features a rack and pinion table support mechanism, a feature often only found on much larger machines, representing excellent value for a machine in this price range.
-
Out of stock
When it is critical to drill a hole at a certain angle or the hole needs to be stopped at a specific depth, there really is no substitute for a dedicated drilling machine. By setting up the work piece and clamping it to the table all guesswork is eliminated and accurate and repeat drilling becomes simple and easy. Record Power have long had a reputation for fine drilling machines and our current range is no exception.Making extensive use of steel and cast iron and driven by a powerful induction motor, the DP58B can be expected to give reliable service for many years. The headstock in particular is made from a large casting to give rigidity and absorb vibration.The large, heavy table is fitted with rack and pinion rise and fall. The machine has 12 speeds, making it suitable for drilling metal as well as wood. This is particularly useful as most woodworkers have the occasional need to drill metal for hinges, brackets and plating etc. and it can be very frustrating to have the right machine for the job but not the right speeds.Record Power have a high reputation for quality drilling machines and we believe that when this machine is compared to others in the market at similar (or greater) prices the value for money it represents will be quickly appreciated.
-
The SABRE range of bandsaws are the next evolutionary step from the highly regarded and market-leading Record Power premium bandsaws. They have built on the success of their premium range by introducing some fantastic new features to the SABRE-350 to make a bandsaw that is more effective, accurate and easier to use than any other machine in its class. Featuring an 1100 W output (1 1/2 horsepower) motor coupled with the heavy-duty cast iron band wheels, the SABRE-350 packs a real punch and can handle cuts to its full capacity with ease. The two speeds, which are slightly faster than comparable machines, make it ideal for cutting non-ferrous metals as well as wood. The cam-action fence adjustment, spring-loaded guides, cam-action blade tension release and double-sided fence mount make this a machine that is so easy to setup and use it leaves you free to concentrate fully on the project at hand.
-
Skip tooth pattern to suit BS400. Also fits Axminster JBS180 & Jet JWBS18
-
With 28 LED bulbs mains powered, Charnwood's magnetic base light is ideal for any situation where better lighting is required. The flexible arm is 370mm long and is fixed onto a magnetic base that can be turned on and off allowing the LED light to be securely attached to any steel or cast iron base. With 28 LED lights it produces better light than many with the added advantage of emitting very little heat. There is a seperate on / off switch for the LED light and it runs off a standard 240v, 13amp socket and comes complete with a 1.2m cable. Ideal for use with;- Bandsaws
- Lathes
- Pillar drills
- Scroll Saws
- Underpinners
Specification
Number of LEDs 28 Brightness 180 Lumens Shaft Length 370mm Weight 1.4kg Rating Trade Warranty 1 Year -
Faceplates are the ideal tool for mounting larger or heavier work, for turning across the grain. This cast iron faceplate is precision machined on external faces to a tolerance of 1/1000th of an inch for each inch of radius and CNC turned for exceptional accuracy and balance. It features concentric circular grooves to aid the centralising of smaller workpieces. -
Designed to hold wood securely without splitting, this drive centre gives superior hold. The opposing tooth profiles mean that as they enter the wood, the fibres are pushed together rather than apart, holding the timber together. -
A good quality tailstock live centre is an essential accessory when turning between centres. Unlike traditional stationery centres, a live centre rotates with the wood, eliminating burning and increasing hold. All Record Power live centres feature high quality bearings to give long life and resist pressure during use. Sealed for life bearings ensure reliable, long lasting operation. -
Woodturners drill chuck, supplied with chuck key. -
Rotating centre with 5/16” bore for long hole boring. Based around a standard duty configuration. Also useful for spindle turning when there is a danger of a centre point splitting the stock. Set comprises: Hollow rotating centre, nose cone for use as standard centre, centring rod. -
1” diameter 4 prong head. Head relieved behind flutes to prevent binding. Supplied with inter-changeable point, pilot and hex key.
